IBM CS821 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 118

background image

Replacing a power supply in the 8001-12C, 8001-22C, 8005-12N, or
8005-22N

Learn how to replace power supplies in the IBM Power System S821LC (8001-12C), the IBM Power
System S822LC for Big Data (8001-22C), the IBM CS821 (8005-12N), or the IBM CS822 (8005-22N) systems.

Procedure

1.

Ensure that you have the electrostatic discharge (ESD) wrist strap attached. If not, attach it now.

2.

Align the power supply with the bay as shown in Figure 81. The fan is on the left; the plug is on the
right. Slide the power supply into the system until the latch locks in place.

3.

Reconnect the power cord. For instructions, see “Connecting the power cords to an 8001-12C,
8001-22C, 8005-12N, or 8005-22N system” on page 86.

Removing and replacing covers on an 8001-12C or 8005-12N system

Learn how to remove and replace the covers for an IBM Power System S821LC (8001-12C) or the IBM
CS821 (8005-12N) system so that you can access the hardware parts or service the system.

Removing the service access cover from an 8001-12C or 8005-12N
system

Learn how to remove the service access cover from an IBM Power System S821LC (8001-12C) or the IBM
CS821 (8005-12N) system.

About this task

Attention:

For safety, airflow purposes and thermal performance, the service access cover must be

installed and fully seated before you power on the system.

Figure 81. Replacing a power supply in the system

80

Power Systems: Servicing the IBM Power System S821LC (8001-12C) or the IBM CS821 (8005-12N)

«
...
94
95
96
97
98
...
»

Содержание CS821























































































































Отзывы:

Нет отзывов

Похожие инструкции для CS821

Бренд: Earlex Страницы: 4

Бренд: SafetySpeed Страницы: 43

Бренд: Patterson Страницы: 16

Бренд: Rapid Страницы: 93

Бренд: Rapid Страницы: 140

Бренд: Vanderbilt Страницы: 18

Performance IntelliSUPPLY PSC15

Бренд: XS Power Batteries Страницы: 24

Бренд: MaxPro PROFESSIONAL Страницы: 50

Бренд: ZALMAN Страницы: 4

DuraSpin DS275-18V

Бренд: Senco Страницы: 56

Бренд: Dahua Technology Страницы: 28

Бренд: Delta Electronics Страницы: 3

Бренд: TDK-Lambda Страницы: 16

Бренд: AP&T Страницы: 3

Бренд: Malibu Boats Страницы: 4

Бренд: H3C Страницы: 15

Бренд: Gude Страницы: 20

Бренд: OKUtools Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды