IBM CS821 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 118

background image

6.

Fasten the two front screws (C) to secure the system to the rack.

7.

Using your labels, reconnect the cables at the rear of the system unit.

8.

If you removed the storage drives, using your labels, replace the drives in their proper locations.

9.

If you removed the power supplies, replace them. For instructions, see “Replacing a power supply in
the 8001-12C, 8001-22C, 8005-12N, or 8005-22N” on page 80.

Power cords

Learn how to disconnect and connect the power cords on IBM Power System S821LC (8001-12C), the IBM
Power System S822LC for Big Data (8001-22C), the IBM CS821 (8005-12N), or the IBM CS822 (8005-22N)
systems.

Disconnecting the power cords from an 8001-12C, 8001-22C, 8005-12N,
or 8005-22N system

Learn how to disconnect the power cords from an IBM Power System S821LC (8001-12C), the IBM Power
System S822LC for Big Data (8001-22C), the IBM CS821 (8005-12N), or the IBM CS822 (8005-22N) system.

Before you begin

Note:

This system might be equipped with two or more power supplies. If the removing and replacing

procedures require the power to be off, then ensure that all power sources to the system are
disconnected.

Procedure

1.

Identify the system unit that you are servicing in the rack.

2.

Label and disconnect the power cords from the system unit as shown in Figure 86 on page 86.

Figure 85. Placing the system into the operating position

Common procedures for servicing or installing features in the 8001-12C or 8005-12N

85

«
...
99
100
101
102
103
...
»

Содержание CS821























































































































Отзывы:

Нет отзывов

Похожие инструкции для CS821

Бренд: C&H Technologies Страницы: 24

Бренд: Davey Water Products Страницы: 4

Бренд: Far Tools Страницы: 33

Бренд: B&B Electronics Страницы: 6

Бренд: Campbell Hausfeld Страницы: 2

Бренд: Parkside Страницы: 91

Бренд: YATO Страницы: 112

Бренд: Image Industries Страницы: 32

Бренд: Oben Страницы: 32

Бренд: Xantrex Страницы: 30

Бренд: YATO Страницы: 88

Бренд: Parkside Страницы: 109

Бренд: Fein Страницы: 59

Бренд: Neilsen Страницы: 16

LIFESTAR 20-1000TUL-DC

Бренд: Vanner Страницы: 14

Бренд: Skil Страницы: 3

Бренд: Crown Страницы: 116

Бренд: Sima Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды