IBM Aptiva 2170 Скачать руководство пользователя страница 38

Страница: 38 / 252

- Pentium III - 550MHz internal, 100MHz external

- Pentium III - 600MHz internal, 100MHz external

- Pentium III - 700MHz internal, 100MHz external

- Pentium III - 750MHz internal, 100MHz external

Memory

•

512-KB Pipeline Burst Static RAM (PBSRAM). Fixed onboard for 2170,
built-in Pentium III processors for 2171/2172

•

8-MB video Synchronize DRAM (SDRAM). Fixed onboard only for 2170
non-UMA model, built-in AGP video adapter card for 2171 and 2172

•

168-pin Synchronous Dynamic Random Access Memory (SDRAM), Dual-
in-line Memory Module (DIMM) sockets.

- 2 memory sockets.

- 8-MB, 16-MB, 32-MB, 64-MB or 128-MB DIMM.

- PC-100 (64-bit, non-ECC, 100MHz, 3.3volt) DIMMs with gold contacts

- Maximum memory is 256 MB.

External Ports

•

Video port (15-pin D-sub connector)

•

Parallel port (25-pin D-sub connector)

•

Serial port (9-pin D-sub connector). 2170 has one serial port while 2171 and
2172 have two.

•

Game/MIDI port (15-pin D-sub connector)

•

Keyboard port (6-pin PS/2 mini-din connector)

•

Mouse port (6-pin PS/2 mini-din connector)

•

Two USB ports.

•

Microphone-in jack

•

Speaker-out jack

•

Line-in jack

Diskette Drive

•

AT-type

•

3.5-in. 1.44 MB slimline diskette drive.

•

3.5-in. 100MB / 250MB ZIP drive

Содержание Aptiva 2170





























































































































































































































































Результаты поиска

Содержание Aptiva 2170

Отзывы:

Похожие инструкции для Aptiva 2170

Бренды по названию

Популярные бренды

IBM Aptiva 2170, Руководство по обслуживанию оборудования

Результаты поиска

Содержание Aptiva 2170

Отзывы:

Похожие инструкции для Aptiva 2170

Бренды по названию

Популярные бренды