5. Wait for successful termination of the download operation. The message
download successful is
displayed. This may also be checked by displaying the TFTP last transfer result through the
command
show tftp.
6. The command
show device displays the new operational code version. It will appears as backup
V3.3.2. This new backup operational code will only become active after a
swap microcode
command completion.
STEP 3. Download Inband the 8265 A-CPSW FPGA picocode if it is a new FPGA level.
1. Configure the TFTP parameters by entering the following commands:
a.
set tftp server_ip address <ip address of the TFTP server>
b.
set tftp file_type fpga
c.
set tftp target_module n (where n is 9 or 11 depending of active A-CPSW position).
d.
set tftp file_name (provide the full path of the file fpga1d12.bin when prompted)
e.
save tftp
2. Verify that you can reach the TFTP server by entering:
ping <ip address of the TFTP server>
(Stop PING by entering&olon. CTL+C)
3. Start the download inband procedure by entering:
download inband
4. When prompted, type
Y to confirm.
5. Wait for successful termination of the download operation. The message
download successful is
displayed. This may also be checked by displaying the TFTP last transfer result through the
command
show tftp.
6. The command
show module n verbose displays the new operational code version. It will appears
as backup 1D12. This new backup FPGA picocode will only become active after a swap FPGA
command completion.
STEP 4. Download inband the 8265 A-CPSW boot microcodeHWT 410 Upgrade the new active
A-CPSW boot microcode as follows:
1. Log on as the administrator on the A-CPSW console.
2. Enter the command:
set device migration not_allowed
3. Upgrade the A-CPSW boot microcode (boot EEPROM) as follows:
a. Configure the TFTP parameters by entering the following commands:
1)
set tftp server_ip address <ip address of the TFTP server>
2)
set tftp file_type boot
3)
set tftp file_name (provide the full path of the file (bootv332.bin) when prompted)
4)
save tftp
b. Verify that you can reach the TFTP server by entering:
ping <ip address of the TFTP
server>
(Stop PING by entering: CTL+C)
c. Start the download inband procedure by entering:
download inband
d. When prompted, type
Y to confirm.
e. Wait for successful termination of the download operation. The message
Download successful
is displayed. This may also be checked by displaying the TFTP last transfer result through the
command
show tftp.
f. The command
show device displays the new boot code version. It appears as V3.3.2. This
new boot code will be active after an A-CPSW reset, and it is located on the flash boot
EEPROM on the Control Point card (ZM36).
STEP 5. Activate the backup A-CPSW
If you have a redundant A-CPSW active the backup by entering (on the active A-CPSW):
1.
set device role secondary
3-16
8265 PD and SG
Содержание 8265 Nways ATM Switch
