manualshive.com logo in svg

IBM 7383, Инструкция по установке и обслуживанию

IBM 7383 - это комплексное устройство, для которого доступно руководство по монтажу и обслуживанию. Вы можете скачать это руководство совершенно бесплатно на нашем сайте. Узнайте все детали установки и обслуживания этого продукта, используя наше руководство.

Поделиться
Скачать
background image

b.

Make sure that the server, operating system, and software are installed
and configured correctly.

Many configuration problems are caused by loose

power or signal cables or incorrectly seated adapters. You might be able to
solve the problem by turning off the server, reconnecting cables, reseating
adapters, and turning the server back on. For information about performing
the checkout procedure, see “About the checkout procedure” on page 132.
For information about configuring the server, see Chapter 3, “Configuration
information and instructions,” on page 101.

6.

See controller and management software documentation.

If the problem is

associated with a specific function (for example, if a RAID hard disk drive is
marked offline in the RAID array), see the documentation for the associated
controller and management or controlling software to verify that the controller
is correctly configured.
Problem determination information is available for many devices such as RAID
and network adapters.
For problems with operating systems or IBM software or devices, go to
http://www.ibm.com/supportportal.

7.

Check for troubleshooting procedures and RETAIN tips.

Troubleshooting

procedures and RETAIN tips document known problems and suggested
solutions. To search for troubleshooting procedures and RETAIN tips, go to
http://www.ibm.com/supportportal.

8.

Use the troubleshooting tables.

See “Troubleshooting by symptom” on page

151 to find a solution to a problem that has identifiable symptoms.
A single problem might cause multiple symptoms. Follow the troubleshooting
procedure for the most obvious symptom. If that procedure does not diagnose
the problem, use the procedure for another symptom, if possible.
If the problem remains, contact IBM or an approved warranty service provider
for assistance with additional problem determination and possible hardware
replacement. To open an online service request, go to http://www.ibm.com/
support/entry/portal/Open_service_request. Be prepared to provide
information about any error codes and collected data.

Undocumented problems

If you have completed the diagnostic procedure and the problem remains, the
problem might not have been previously identified by IBM. After you have
verified that all code is at the latest level, all hardware and software configurations
are valid, and no light path diagnostics LEDs or log entries indicate a hardware
component failure, contact IBM or an approved warranty service provider for
assistance.

To open an online service request, go to http://www.ibm.com/support/entry/
portal/Open_service_request. Be prepared to provide information about any error
codes and collected data and the problem determination procedures that you have
used.

Chapter 4. Troubleshooting

131

Содержание 7383









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7383

YORKVILLE YX Series Owner'S Manual preview
YX Series
Бренд: YORKVILLE Страницы: 12
YORKVILLE TWO Series Service Manual preview
TWO Series
Бренд: YORKVILLE Страницы: 45
Conrad 28 30 29 Operating Instructions Manual preview
28 30 29
Бренд: Conrad Страницы: 8
Xigmatek Elysium II User Manual preview
Elysium II
Бренд: Xigmatek Страницы: 17
Xigmatek Gaming Y Pro User Manual preview
Gaming Y Pro
Бренд: Xigmatek Страницы: 14
Sony SPORTS PACK SPK-HCD Service Manual preview
SPORTS PACK SPK-HCD
Бренд: Sony Страницы: 6
Toshiba TR1X426110 Owner'S Manual preview
TR1X426110
Бренд: Toshiba Страницы: 24
Toshiba Canvio HDNB120XKEG1 User Manual preview
Canvio HDNB120XKEG1
Бренд: Toshiba Страницы: 40
Toshiba Canvio AeroCast HDTU110XKWC1 User Manual preview
Canvio AeroCast HDTU110XKWC1
Бренд: Toshiba Страницы: 60
Tripp Lite U357-025-2 Owner'S Manual preview
U357-025-2
Бренд: Tripp Lite Страницы: 24
BEL cinch ModICE LE 30 I/O Assembly Instructions Manual preview
cinch ModICE LE 30 I/O
Бренд: BEL Страницы: 11
ZALMAN K1 REV.A User Manual preview
K1 REV.A
Бренд: ZALMAN Страницы: 16
CommScope Flex Frame Splice Cabinet User Manual preview
Flex Frame Splice Cabinet
Бренд: CommScope Страницы: 20
Ratoc Systems FireDock FR-DK1 User Manual preview
FireDock FR-DK1
Бренд: Ratoc Systems Страницы: 21
MTX X3-17-SW-D Owner'S Manual preview
X3-17-SW-D
Бренд: MTX Страницы: 12
Nanoxia CoolForce 1 Manual preview
CoolForce 1
Бренд: Nanoxia Страницы: 15
Fantec MB-X5U31H Manual preview
MB-X5U31H
Бренд: Fantec Страницы: 8
RAID 4-Bay User Manual preview
4-Bay
Бренд: RAID Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды