2. Error messages may displayed if some optional files cannot be found. This can
happen on a save or on a restore.
3. The “Save/Restore Customer Configuration” icon in the 2074 Utilities folder may
be used instead of typing CFGSR into an OS/2 window.
4. If the 2074 Load CD is reloaded onto a system, an initial menu (called from
STARTUP.CMD) will ask you to choose between:
1. New Installation
2. Restore Saved Customer Configuration
Choosing selection 2 is the same as typing CFGSR RESTORE.
Method
The data was put on the diskette by using the COPY command or the AWSSRAM2
command and was restored with COPY or with AWSLRAM2. If a saved diskette
was damaged, you might be able to retrieve and restore parts of the configuration
by using these commands.
Loading the 2074 Hard Drive
Although the 2074 hard drive is normally loaded by IBM manufacturing, you may
need to reload the hard drive for several reasons:
1. The hard disk has permanent or intermittent hardware problems.
2. The OS/2 system is malfunctioning, perhaps due to data corruption.
3. IBM Product Engineering requests the return of the hard disk for dump analysis.
4. A mandatory EC requires a new level of 2074 Load CD to be installed.
5. To Reset a lost OS/2 password.
The procedure for loading the 2074 hard disk is as follows:
1. Locate the “IBM 2074 Load CD”.
2. If you are replacing a faulty hard drive, and cannot get an OS/2 Window, skip
to step 4. Otherwise, run “Save/Restore Customer Configuration”. This can be
done by opening the 2074 Utilities folder and double-clicking on the
Save/Restore icon. It can also be run by typing
CFGSR SAVE
at an OS/2
prompt.
Note:
You will need a blank, formatted 1.44MB diskette.
This will save all the customer specific files to the floppy diskette, so they can
be reloaded after the hard disk is restored.
3. Remove the Customer Configuration Save diskette from drive A:, label it, and
slide the write-protect tab to the open (protected) position.
4. Place the 2074 Load CD into the CD-ROM drive.
Note:
For IBM CEs, a new Load CD is available from an ECA whenever
levels change.
5. Shutdown OS/2 (Ctrl-Alt-Del). Power off the system if you are replacing the
hard drive; else leave it powered on to reboot.
6. If you are replacing a faulty hard drive, do it now.
7. Power-on the system (or it is rebooting)
8. The system will boot DOS from the 2074 Load CD.
9. A selection screen will be displayed. Read the choices
carefully
:
3-12
: 2074 Console Support Controller Installation and Maintenance Information
|
|
|
|
|
|
|
|
Содержание 2074
