manualshive.com logo in svg

IBEX TS51C, Инструкция по сборке и быстрому запуску

Поделиться
Скачать
IBEX TS51C Скачать руководство пользователя страница 15

Ibex TS51C Drum Mower Assembly Guide 

Copyright 2020 Ibex Equipment Co. 

 

Page | 15 

 

Pivot Restrictor 

The drum unit pivots to adjust to the terrain while cutting. The pivot restrictor keeps the mower from pivoting 

too far and also secures it while in transport mode. Gather the parts shown in Figure 31 with two 19 mm 

wrenches. Take care to face the head of the bolt out as the clearance with the handle is tight. Only 3 of the 4 

washers are used. 

 

 

Figure 31 restrictor plate with hardware 

 

Figure 32 plate shown installed from side 

Assemble as shown in Figure 32. The clamp handle should be tightened during transport to keep the drums 

from pivoting down and possibly dragging. During mowing, the handle is loosened so that the mower pivots 

freely within the range allowed by the slot in the restrictor plate. 

Guard Installation 

The front guard frame has 6 holes and a pin that slides into the tubing of the rear frame as shown. 

Содержание TS51C























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды