IBC VX Series Скачать руководство пользователя страница 92

Страница: 92 / 111

SIM Status Indicators

LED 1

LED 2

State

Description, LED status

indication

Heating

Rapid flash

Igniting

Off

Flashing

Lockout

Flash alternately with
LED 2

Flash alternately with
LED 1

Fail-safe

Boiler requires a power cycle

Table 13

SIM+ LED status Indicators

8.1.4.2 Resetting a boiler after a LWCO lockout

A boiler in a lockout condition due to a LWCO error will need to be reset.

1. Go to

Clear Errors

Yes

2. Check that there is enough water in the system and that the boiler is pressurized.

3. To reset the boiler, go to

SIM Menu

LWCO Test

Reset

Yes

4. Run the boiler to ensure that the error has been cleared.

5. If the error persists, perform a LWCO test. Go to

SIM Menu

Hi-Limit Test

Run the test to check if the low water cutoff sensor is opening.

8.1.4.3 Resetting a boiler after a hi-limit temperature lockout

A boiler in a lockout condition due to a hi-limit temperature error will need to be reset.

1. Go to

Clear Errors

Yes

2. Check that there is no air trapped in the system and that the boiler is pressurized.

3. To reset the SIM Module, go to

SIM Menu

Hi-Limit Test

Reset

Yes

4. Run the boiler to ensure that the error has been cleared.

5. If the error persists, perform a hi-limit test. Go to

SIM Menu

Hi-Limit Test

Run the test to see if the hi-limit switch is operational. You can also perform this test for
gasket blowouts.

Section: Troubleshooting

Содержание VX Series
















































































































Результаты поиска

Содержание VX Series

Отзывы:

Похожие инструкции для VX Series

Бренды по названию

Популярные бренды

IBC VX Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VX Series

Отзывы:

Похожие инструкции для VX Series

Бренды по названию

Популярные бренды