IBC SFT-199 Скачать руководство пользователя страница 59

Страница: 59 / 70

5-7

TROUBLESHOOTING

SFT 199 TANKLESS WATER HEATER

5.4.4 Burner ignites loudly

POSSIBLE CAUSES

ANALYSIS

SOLUTION

Inlet pressure is too high.

→ Yes

↓No

The home pressure regulator may be defective. In that

case, contact the energy company.

Ignition distance is incorrect.

→ Yes

↓No

Replace the ignitor including the ignition cable.

Gas-air control is not correctly
adjusted.

→ Yes

Check and/or replace the ignition cable.
Replace the ignition unit in the top cover.
Replace the ignitor.

5.4.5 Burner resonates

POSSIBLE CAUSES

ANALYSIS

SOLUTION

Gas inlet pressure lower than 5“ w.c.
or sometimes disappears.

→ Yes

↓No

The home pressure regulator may be defective. Contact

the energy company.

There is recirculation of fl ue gases.

→ Yes

↓No

Check the fl ue and air supply duct.

Gas-air control is not correctly adjusted.

→ Yes

↓No

Check the adjustment

Burner seal is defective.

→ Yes

↓No

Replace the burner seal.

Burner is defective.

→ Yes

Replace the burner.

Содержание SFT-199







































































Результаты поиска

Содержание SFT-199

Отзывы:

Похожие инструкции для SFT-199

Бренды по названию

Популярные бренды

IBC SFT-199, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SFT-199

Отзывы:

Похожие инструкции для SFT-199

Бренды по названию

Популярные бренды