IBA 14.132000 Скачать руководство пользователя страница 54

Страница: 54 / 67

Manual

ibaLink-VME

Issue 1.8

9.3

Cascade with 3Mbit mode

Up to eight cascadable devices may be cascaded in a single daisy-chain of fiber-optic

devices (Channel 1 only). Cascadable devices are: ibaLink-VME, ibaLink-SM128V,

ibaPADU-8/-16/-32 and ibaNet750, but not ibaLink-SM-64, because its cascading con-

cept is different.
The total of 64 a/d signals to be transmitted over one fiber-optic link is subdivided into

eight slots of eight a/d signals each. The slots are divided between several participants

in a cascade.
In this mode, each ibaLink-VME participating in the chain is forwarding the 8 incoming

data slots on its fiber optic input towards its fiber optic output, only replacing one or more

successive slots (S2 Range switch) by the data provided in the VME transmit buffer. The

first slot to be replaced is configured using the S3 Address switch.
Independent from the S2/S3 switches, the data of the 8 incoming slots is always available

in the VME receive buffer.
The setting of S1 switch is 0 (zero) or 1 in cascade mode.

Example 1: System Topology for Daisy-Chain of 8 ibaLink-VME with equal ranges

Figure 24 Cascade mode with 8 x ibaLink-VME

Eight ibaLink-VME interface cards are daisy-chained with each card transmitting 8 sig-

nals for the resulting daisy-chain telegram. The address switch position determines the

slot to be occupied. After the last ibaLink-VME card all slots are filled with data. The FO

input of the ibaFOB card receives 8 x 8 = 64 signals.
The second link of the card (Channel 2) may be used for independent transmission of up

to 64 a/d signals.

Содержание 14.132000




































































Результаты поиска

Содержание 14.132000

Отзывы:

Бренды по названию

Популярные бренды

IBA 14.132000, Руководство пользователя

Результаты поиска

Содержание 14.132000

Отзывы:

Бренды по названию

Популярные бренды