manualshive.com logo in svg

IAME Parilla X30 125cc RL, Руководство по капитальному ремонту

Поделиться
Скачать
IAME Parilla X30 125cc RL Скачать руководство пользователя страница 22

                                                                                                                                                                            

MAN-044/A 

20

 

 

 
- INSTALL GEAR ON THE CRANKSHAFT 
 (LETTER “A”  TO BE VISIBLE )

  

ALIGNING THE 

REFERENCE NOTCHES ON THE

 

INTERNAL 

TEETH WITH REFERENCE NOTCHES ON

 

  THE EXTERNAL TEETH OF THE 2 GEARS 
 (CHECK BOTH GEARS TO BE ON THE SAME 

LEVEL). 

 (see Fig.18) 
 

NOTE: 
IF GEARS HAVE NOT BEEN REPLACED, 
REINSTALL THEM  IN  THEIR ORIGINAL 
POSITION . 
( IDENTIFY THE GEAR MARKED DURING THE 
DISASSEMBLING AND ASSEMBLE IT ON 
CRANKSHAFT). 

 
 
 
- INSTALL SEEGER ON THE CRANKSHAFT 
  AND BALANCE SHAFT. 
  (see Fig.19) 
 
  

(PLIERS FOR RETAINING RINGS) 

 
 
 

FOLLOW THE RECOMMENDATIONS AS PER 
ATTACHMENT. 

 

NOTE: 
IN THE ENGINES MNUFACTURED AFTER 
SEPTEMBER ’05, THE FIXING OF THE GEAR 
ON THE CRANKSHAFT IS MADE BY A 
SPACER WITH AN “OR” WHICH IS PUSHED 
AGAINST GEAR BY THE IGNITION ROTOR.

 

 

 

5.

 

 

INSTALLING THE STARTER 
 

- PLACE STARTER IN THE CRANKCASE SEAT 
  (see Fig.20). 
  OIL “O’RING”  BEFORE INSERTING. 
  CHECK THAT THE CLAMP FIXING THE 

STARTER CABLE  IS IN PLACE. 

 

  N°2  ALLEN SCREWS M6x35 
  TORQUE AT A 8÷10 Nm (70 ÷ 90 in-lb). 
 
 (5mm ALLEN SCREW – T TYPE) 

 

 

6. 

 
INSTALLING  THE GEAR COVER 

- PLACE GASKET ON CRANKCASE. 
  (see Fig.21). 
 
 

 

Fig.18

Fig.19

Fig.20

Fig.21

Содержание Parilla X30 125cc RL







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды