IAME Parilla x30 125cc RL-TaG Скачать руководство пользователя страница 17

Страница: 17 / 47

MAN-043/B

2.8

ELECTRICAL CONNECTIONS
(Refer to the attached electrical
schematic).

NOTE:
For a correct installation follow the under
shown instructions.

2.8.1

INSERT THE BATTERY STRAP IN THE

BATTERY SUPPORT (SEE FIG. 13).

2.8.2

PLACE THE BATTERY SUPPORT BOX

IN THE FRONT OF THE CHASSIS (UNDER
THE FRONT FAIRING) AND FIX IT WITH THE
CLAMPS TO THE LOWER STEERING
COLUMN SUPPORT TUBES (M6x25
SCREWS– SEE FIG. 14).

TORQUE AT 8 ÷ 10 Nm (70÷ 90 in-lb)

THE SUPPORT BOX MUST BE FIXED WITH
AT LEAST ONE BOLT FOR EACH CLAMP.
FIX THE BOX WITH MORE THAN ONE BOLT
DEPENDING ON THE TYPE OF CHASSIS.

NOTE:
THE BOX AND CLAMPS ARE PROVIDED
WITH VARIOUS HOLES WHICH ALLOW
INSTALLATION ON ALL KIND OF CHASSIS.

10mm BOX WRENCH

2.8.3

INSERT THE BATTERY IN THE BOX

AND FASTEN WITH THE BATTERY STRAP
(SEE FIG. 15).
POSITION THE BATTERY TERMINALS AS
SHOWN ON THE FIGURE.

ATTENTION:
PAY ATTENTION NOT TO SHORT-CIRCUIT
THE BATTERY TERMINALS AS THE
BATTERY COULD BE DAMAGED BEYOND
REPAIR.

2.8.4

POSITION THE WIRING HARNESS

STARTING FROM THE ENGINE AND ALONG
THE RAIL, THE STEERING COLUMN AND
UNDER THE FRONT PANEL FAIRING (SEE
FIG. 16).
TIGHTEN WITH PLASTIC CLAMPS.

ATTENTION:
NEVER LET THE HARNESS GET IN TOUCH
WITH THE GROUND OR WITH ROTATING
PARTS AS IT COULD BE DAMAGED
BEYOND REPAIR .

Fig.14

Fig.13

Fig.15

Fig.16

Содержание Parilla x30 125cc RL-TaG
















































Результаты поиска

Содержание Parilla x30 125cc RL-TaG

Отзывы:

Похожие инструкции для Parilla x30 125cc RL-TaG

Бренды по названию

Популярные бренды

IAME Parilla x30 125cc RL-TaG, Инструкция по сборке и руководство пользователя

Результаты поиска

Содержание Parilla x30 125cc RL-TaG

Отзывы:

Похожие инструкции для Parilla x30 125cc RL-TaG

Бренды по названию

Популярные бренды