i3 International S81 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 205

background image

24

Green Ethernet Parameters:

Items

Description

Optimize EEE

The switch can be set to optimize EEE for either best power saving or least traffic latency.

Port

The switch port number of the logical port.

ActiPHY

Link down power savings enabled. ActiPHY works by lowering the power for a port when
there is no link. The port is powered up for short moments in order to determine if a cable is
inserted.

PerfectReach

Cable length power savings enabled. PerfectReach works by determining the cable length
and lowering the power for ports with short cables.

EEE

Controls whether EEE is enabled for this switch port. For maximizing power savings, the
circuit isn't started once data is  ready for transport from a port, but is instead queued  until
a  burst  of  data  is  ready  to  be  transmitted. This will give some traffic latency. If desired it
is possible to minimize the latency for specific frames, by mapping the  frames  to  a  specific
queue  (done  with  QOS),  and  then  mark  the  queue  as  an  urgent queue. When an urgent
queue gets data to be transmitted, the circuits will  be powered up at once and the latency
will be reduced to the wakeup time.

EEE Urgent Queues

Queues set will activate transmission of frames as soon as data is available. Otherwise the
queue will postpone transmission until a burst of frames can be transmitted.

Ports Configuration

This Section describes how to configure the Port detail parameters of the switch. This includes enabling and disabling the
ports of the switch as well as monitoring the ports content and status.

«
...
23
24
25
26
27
...
»

Содержание S81














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S81

Бренд: GE Страницы: 20

Бренд: Hama Страницы: 18

COOPER POWER SERIES

Бренд: Eaton Страницы: 32

Бренд: Keithley Страницы: 452

Pow-R-Line SPX0361126

Бренд: Eaton Страницы: 584

Signature ANTENNA GENIUS 8x2 v2 PLUS

Бренд: 4O3A Страницы: 57

Бренд: Eaton Страницы: 36

Бренд: Cumberland Страницы: 2

Бренд: National Instruments Страницы: 12

Бренд: Comm-Tec Страницы: 10

Бренд: Cabletron Systems Страницы: 105

Бренд: Omron Страницы: 4

Бренд: ATEN Страницы: 2

IES6300PRO Series

Бренд: 3onedata Страницы: 5

Бренд: Lindy Страницы: 2

Бренд: Star Trac Страницы: 3

Бренд: Omega Страницы: 4

Бренд: Hama Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды