USER MANUAL
Page -2-
i3C762 PTZ Joystick Keyboard
PROTOCOL/BAUD RATE
Set the keyboard protocol type and baud rate.
Press [function] to display the current keyboard
communication protocol and baud rate. To change the
communication protocol, use
[wide]
to select a desired
communication protocol and press
[tele]
to select an appropriate baud rate. Press
[enter] to save and exit.
PORT2 TYPE
Set Port2 signal connection to receiving or transmitting
mode. The first row shows the function type and the
second row displays the function status. Press
[wide]
or
[tele]
to change the setting status to be RX (Receiving) or TX (Transmitting) and
then press
[enter]
to save and exit.
EXIT
To exit from function options. Press [enter] to confirm.
Visit our YouTube channel for training videos.
Press
[function]
to display the current keyboard communication protocol and baud rate.
1. PROTOCOL
PELCO D
2400
Preset / Patrol / Pattern Setup
Confirm the speed dome ID address you want to control. Refer to the Speed Dome Camera
Manual for ID address setup. Enter the Camera ID address of the speed dome to control it.
CAMERA ID: 1
PELCO D
2400
Enter:
[cam id]
+
NNN
+
[enter]
The first row of this display shows the current Camera ID,
the second row awaits new Camera ID input number from
0~255.
CAMERA ID: 1
CAMERA ID: 0
Enter:
[set]
+
NNN
+
[enter]
The second line of the display awaits a new preset
number. Move the speed dome to the preset location, then
enter the preset ID to save it.
CAMERA ID: 1
SET ID:
0
Enter:
[preset]
+
NN
+
[enter]
The second row awaits the preset number input to call on
a saved preset
CAMERA ID: 1
PRESET NO.: 0
Enter:
[set]
+
NN
+
[enter]
The second line of the display awaits an existing preset
number. Move the speed dome to a new preset location,
then enter the preset ID to overwrite the existing preset
with the new camera position.
CAMERA ID: 1
SET ID:
0
Enter:
[patrol]
+
N
+
[enter]
Patrol function calls up a group of previously configured camera presets. The preset group
CAMERA ID: 1
PATROL NO: 0
Enter:
[pattern rec]
+
N
+
[enter]
(where N = number 1 ~ 4) to start recording; then use the joystick to control and create a
pattern route. Finally, press [pattern rec stop] to stop recording.
CAMERA ID: 1
PATTERN NO: 0
Enter:
[pattern]
+
N
+
[enter]
to call the speed dome
pattern scanning.
CAMERA ID: 1
PATTERN NO: 0
Change Keyboard Communication Protocols/Baud Rates
Change Camera ID
Set Preset
Call Preset
Overwrite Preset
Call Patrol (Preset Touring)
Record Pattern
Call Pattern
Enter:
[shift]
+
[2]/[4]/[6]/[8]
. Press
[shift]
to start adjusting camera’s pan/tilt. Press
2/4/6/8 directional buttons to fine-tune the pan/tilt direction of your speed dome camera.
Speed Dome Pan/Tilt
[auto scan]
Ativate auto-scanning. The speed dome will
continually make a 360° horizontal rotation. To stop scanning,
move the joystick in any direction.
[info]
Display information of firmware version, protocol,
camera address and baud rate on the display.
[menu]
While this key is pressed, on-screen display menu will be shown on
the monitor’s screen. Move the joystick [up] or [down] to roll the optical
cursor up and down to select options and use [open] or [close] to change
the selected options.
[color/mono]
Switch to a color mode or black/white mode. (Note: this function is
available only for the speed domes with the day/night function).
[function]
The [function] key contains the following functions of “1. PROTOCOL”,
“2. PORT2 TYPE”, and “3. EXIT”. Use
[near]
or
[far]
to cycle through the
functions.
1. PROTOCOL
PELCO D
2400
2. PORT 2 TYPE
RX
3. EXIT
Master/Slave Control Operation Procedure
The first row of the standby display shows the Camera ID
address of the current speed dome camera, the second
row shows the camera’s protocol and baud rate.
To change the communication protocol, use the
[wide]
key to select a desired protocol. To change the baud rate,
use the
[tele]
key to select an appropriate baud rate.
Press
[enter]
to save and exit.
(Preset Tour) must be first configured in the speed dome
OSD menu. i3C762 supports up to 4 unique Patrols. The
second line of the display awaits an existing Patrol number
input from 0 ~ 4.
Pattern function is the speed dome’s pan/tilt movements
recorded by the i3C762. This function does not rely on
the Camera’s presets. i3C762 supports up to 4 unique
Patterns.
Use
[cam id]
or
[enter]
to decrease or increase the pan/
tilt degree value. The higher the value, the greater the
pan/tilt degree.
Hot Keys
Certain i3C762 buttons act as “hot keys” or shortcuts for specific functions.
[open]
Enlarge lens IRIS
[wide]
Zoom out
[close]
Decrease lens IRIS
[tele]
Zoom in
[near]
Focus near
[lock]
Lock all functions
[far]
Focus far
[origin]
Return to home position
Joystick Control Pan/Tilt Panel
The gearshift joystick is used to control rotation/
elevation direction and speed of the Pan / Tilt
functions of a speed dome camera. The angle of the
joystick shown determines the rotation/elevation
speed. The rotation speed can be adjusted evenly
by changing the inclination angle of the joystick.
During scanning, the camera will auto-focus on a
clear object.
A 3D joystick can be used to zoom the lens in/out. Twist in the clockwise direction to
Zoom In and Counter-clockwise to Zoom Out.
Connection and Setup
B) “Star” Connection
When connecting several
keyboards together, please follow
instructions in the PORT2 TYPE
section to set each keyboard’s
Port Mode. Choose RX
(Receiving) mode for PORT 2
on the Master Keyboard as a
communication output port for
Slave Keyboard Port 1.
A) Daisy-Chain Connection
FINE TUNE: P/T
DIRECTION: 4
PORT1
DC12V
RS232
PORT2
RS485-
RS485+ RS485-
RS485+
Master i3C762
PORT1
DC12V
RS232
PORT2
RS485-
RS485+ RS485-
RS485+
Slave i3C762
PORT1
DC12V
RS232
PORT2
RS485-
RS485+ RS485-
RS485+
Speed Domes
No.1
No.254 No.255
. . .
i3C762
PORT1
DC12V
RS232
PORT2
RS485-
RS485+ RS485-
RS485+
No.1
No.2
No.3
No.4
i3C762
