SAFETY
When installing your Ax85 camera be sure to avoid:
•
excessive heat, such as direct sunlight or heating appliances
•
contaminants such as dust and smoke
•
strong magnetic fields
•
moisture and humidity
•
areas with mechanical vibrations
•
fluorescent lamps or objects that reflect light and unstable light sources
•
temperatures below -40° C (-40° F) and above 50° C (122° F).
To avoid electrical shock and to preserve the product warranty,
DO NOT
disassemble the
camera. Refer servicing to qualified personnel only.
POWER SUPPLY
Ensure the supplied voltage meets the power consumption requirements of this camera
before powering the camera on. Incorrect voltage may cause irreparable damage to the
video camera and will effectively void the camera warranty.
Ax85 requires AC24V or PoE+ power.
CLEANING
•
For maximum optical clarity, the camera dome or lens must remain clean. Use a soft,
dry cloth to remove finger prints or dust from the dome cover.
•
Use a blower to remove dust from the lens.
•
Clean the body with a soft, dry cloth. If it is very dirty, use a cloth dampened with a
small quantity of neutral detergent, then wipe dry.
•
Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finishes.
PACKAGE CONTENTS
Ensure that the items received match those listed on the order form and the packing slip.
In addition to this manual and a fully assembled camera, the dome camera packing box
includes:
A.
Standard RJ45 Connector x2
B.
Dessicant x1. Use in all outdoor installations.
Attach to the underside of the camera’s inner
liner/shroud.
C.
Round Head Screw (Tapping Type) w/ O-ring x4
D.
Plastic Anchor x4
E.
Surface Mount template x1
F.
Flush Mount template x1
G.
Security torx bit x1
H.
Long Machine type screws x3
(for Flush Mounting with back box installations)
CAMERA PARTS AND DEFINITIONS
Quick Start Guide
8MP Infrared Outdoor IP Dome Camera w/ Motorized Lens
Ax85
i3-TRNG-CAMS-
Ax85.
indd
Rev
.
190911
1.
Back box. Camera’s back box comes with six (6) 90% pre-drilled hole dimples.
For surface mounting, complete drilling a minimum of two (2) holes.
2.
Camera module / second housing.
3.
Tilt bracket with locking screw
4.
Inner liner / Shroud. Inner liner is attached to the camera module but can be
partially detached for easier lens adjustment. Attach the desiccant to the inside of
the Inner Liner, without obstructing the lens movement.
5.
IR board
6.
Screws securing the dome bubble housing to camera module (x3, silver)
7.
Dome bubble housing / Dome cover
8.
Lexan bubble
9.
3/4” waterproof rubber plug. For best waterproof performance, use a network cable
5mm or more in diameter. To maintain IP67 waterproof rating, use sealant on the
threads during installation. If using the side conduit hole, replace the rubber plug
with the metal plug from the side conduit. Rubber plug is not recommended for use
in the side conduit hole.
10.
3/4” side conduit hole with metal plug. If using the side conduit hole, remove the
metal plug and use it instead of the rubber plug in the top conduit hole. To maintain
IP67 waterproof rating, use sealant on the threads during installation.
11.
Six (6) 90% pre-drilled hole dimples.
12.
Reset pin-hole button. Press for 1 second to reboot the camera.
13.
Default pin-hole button. Press for 6 seconds to restore camera settings to factory
defaults.
14.
Service Video Output RCA Port. Connect an analog service monitor for a live image
output preview.
15.
Screws attaching camera module to the back box (x3, silver)
16.
Screws to engage locking arms (x2, black)
17.
Micro SD Card slot for on-camera video storage. (microSD card sold separately)
Lens Direction
GUIDE PATTERN
Scan this QR code or visit
www.i3international.com
to
view and download the full User Manual for this camera. Also
available for download is the
AnnexxusConfigurationTool
or ACT program used to locate and configure your cameras
with your SRX-Pro software. This program is already installed
in SRX-Pro v3.3.3.69 and higher. Please contact our Technical
Support team if you have any questions or concerns regarding
camera installation or you require software services or
support. Technical support can be reached by email at:
or by phone toll free
1.877.877.7241.
QR Code to Complete
User Manual / ACT
1
2
5
3
4
6
7
8
F
G
GUIDE PATTERN
Cut Line
Camera Outline
A
C
D
H
E
B
10 11
9
9
63 mm (2.5”)
63 mm (2.5”)
84 mm (3.3”)
147 mm (5¾”)
68 mm (2.67”)
94 mm (3.7”)
158 mm (6¼”)
DEFAULT
RESET
MONITOR
RESET
MONITOR
DEFAULT
12
13
14
15
15
15
16
16
17
