Control Panel is located under the dome cover. Remove inner liner for easier access.
Service-BNC Video Output
Selection Switch:
Switch to
“Service” for Service Port video
output; switch to “BNC” to display
video from the camera’s BNC port.
The default setting is “Service”.
Default:
To reset all settings of the
unit to factory default, press and
hold for 5 seconds.
Reset:
Press to reboot the unit.
Service Video o/p:
For monitor output. Use the BNC cable provided with the camera’s
accessories.
CAMERA CONTROL PANEL
Ax61/Ax62-series 3MP IP Dome Camera
QUICK START GUIDE
i3 INTERNATIONAL INC.
1.866.840.0004
www.i3international.com
Canada 780 Birchmount Road, Unit 16,
Scarborough, ON, M1K 5H4
1. Camera dome, top view
a. Side conduit hole (1/2”). Outdoors use sealant to maintain IP67 rating.
b. Top conduit hole (3/4”) (can also be used for pendant mount). Outdoors use
sealant to maintain IP67 rating.
c. PoE connector (Bottom case must be removed to reveal connector)
d. Video output connector (Bottom case must be removed to reveal connector)
2. Bottom case
3. Camera base
4. Dome cover
5. Focus lever (Ax62-series only)
6. Zoom lever (Ax62-series only)
DISASSEMBLING THE CAMERA
Use the Hex key to remove the dome cover. Then, loosen 3 screws on camera base (#2).
CONNECT CAMERA TO i3 SRX-PRO SERVER
Connection Type 1:
1. Bottom case
2. Camera base
3. Tilt adjustment bracket
4. Inner liner.
Attach the desiccant to the
inside of the inner liner for
Ax62V models only. (#15 on the
Accessories list)
5. Dome cover
6. Anti drop hook
1
2
3
4
5
1. Rotate 3D assembly
in base for horizontal
adjustment
2. Loosen screw and adjust
Tilt. Tighten screw when
desired vertical angle is
achieved.
3. Turn axis ring for horizontal
rotation.
4. Focus lever
5. Zoom lever
CAMERA ADJUSTMENTS
i3 SRX-Pro Server
Crossover direct connection
LAN
i3 SRX-Pro Server
Via Gigabit Switch
Connection Type 2:
6
Camera’s default IP:
192.0.0.16
.
Default Login/Password:
FW ver. i3_00_026-40 | Login:
admin
/ PW:
1234
FW ver. i3_00_39-51, or higher | Login:
i3admin
/ PW:
i3admin
U.S.A 4450 Witmer Industrial Estates Unit 4
Niagara Falls, NY 14305
QR Code to Complete
User Manual
1.
Close SRX-Pro Server software by pressing
Alt+Shift+Ctrl+F4
.
2.
Write down the IP address on the onboard NIC (LAN) (or on NIC1 if your SRX-Pro
Server has two onboard NIC cards).
3.
Connect your camera to i3 SRX-Pro Server (see diagram above).
4.
Turn on your Annexxus camera.
5.
It may be necessary to download and install AnnexxusConfigTool (ACT) from our
website (www.i3international.com). Follow the ACT installation instructions until
the application has been successfully installed on your SRX-Pro Server. For SRX-
Pro v3.3.3.69 and above ACT is already installed.
6.
Either double-click i3 Annexxus Configuration Tool icon on the desktop to launch
the ACT application or click the “ACT Config Tool” button on the IP Camera Tab
in SRX-Pro.
7.
ANNEXXUS Configuration Tool window will display a list of active network
cameras.
8.
Select the desired Annexxus camera in the list (left-click).
9.
In the
Device(s) Communication
area, enter the new IP Range (address) and
Subnet Mask of the camera. The new camera IP address must match the IP
range of your SRX-Pro LAN or NIC1 card (see Step 2).
E.g. If your SRX-Pro Server’s IP address is 192.138.10.122, change your
Annexxus camera’s IP address to 192.138.10.XXX.
Remember: Annexxus Cameras cannot share an IP address, each camera
requires its own unique IP address.
10.
Make sure the
Default Account
checkbox is checked off.
11.
Click
Update
. Wait a few moments for a successful confirmation message.
12.
Repeat Steps 9-12 for all detected Annexxus cameras in the ACT application
OR Select multiple cameras (Ctrl + left click) and enter IP range to assign IP
addresses sequentially to the selected cameras.
13.
Once the IP address of the Annexxus camera(s) has been changed, make sure
you can connect to the camera(s) through Internet Explorer:
a.
Launch Internet Explorer and enter the IP Address you have just assigned to
your Annexxus camera. The password window should be displayed.
b.
Enter the default camera User Name:
i3admin
and default Password:
i3admin
c.
Annexxus camera interface will be displayed in the Internet Explorer
window. You should be able to see the camera image on the screen.
If you do not see the camera image on the screen, call i3 International tech
support for troubleshooting tips: 1.877.877.7241
14.
Make sure that the latest version of GiPi updater is installed on your SRX-Pro
Server. You can download the updates from ftp://files.123ip.com/drivers/gipi.
Please contact i3 Technical Support team for access information.
15.
Once the latest GiPi updater has been installed, restart i3 SRX-Pro Server.
16.
Log In and go to the
Setup
->
IP Camera
tab.
17.
Click the
Search
button to display connected Annexxus cameras.
18.
Select the detected camera in the list and click
Select
.
19.
In the
Select IP Camera window, enter the default camera User Name:
i3admin
and default Password:
i3admin
, then click
Add
.
20.
The selected camera will be added to the IP Camera list.
21.
Assign the IP camera to the SRX-Pro video channel in the
Ch. In.
column.
22.
Select
i3 GiPi
from the
PTZ
column to enable motorized lens’ autofocus feature.
23.
Your Annexxus camera is now connected to SRX-Pro Server and is ready to
record. You may change resolution and frame rate for the Annexxus camera in
the IP Camera tab menu or you may choose to configure the camera’s advanced
settings.
