User Manual
5MP Outdoor IR HD Analog Dome w/ Motorized Lens
Am73
Thank you for purchasing i3 International’s Am73 High Definition indoor/outdoor analog
dome camera. Your camera is equipped with a motorized vari-focal 2.7-13.5mm @
F1.6-F2.4 lens. The lens can be controlled through IE interface of the i3 encoders/
standalone DVRs, or through SRX-Pro Server/VPC.
IMPORTANT: Am73 is set to HD-Analog 2MP resolution. To use 5MP HD-Analog access
camera menu and set the resolution to 5MP.
See CHANGING VIDEO FORMAT section.
SAFETY
When installing your Am73 camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light and unstable light sources
• temperatures below -40°C (-40°F) and above 50°C (122°F)
POWER
This camera accepts DC12V and AC24V power.
Maximum power consumption: 8W.
Ensure the supplied voltage meets the power consumption requirements of this camera
before powering the camera on. Incorrect voltage may cause irreparable damage to the
video camera and will effectively void the camera warranty.
CLEANING & SERVICING
For maximum optical clarity, the camera dome or lens must remain clean. Use a soft,
dry cloth to remove finger prints or dust from the dome cover.
• Use a blower to remove dust from the lens.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finishes.
• To avoid electrical shock and to preserve the product warranty, DO NOT
disassemble the camera. Refer servicing to qualified personnel only.
PACKAGE CONTENTS
Ensure that the items received match those listed
on the order form and the packing slip. In addition
to this manual and a fully assembled camera, the
dome camera packing box includes:
A.
Plastic Anchor x3
B.
Round Head Screw
(Tapping Type) x3
C.
Waterproof tape x2
D.
Surface Mount template x1
E.
Security Torx bit
1.
Long screws (pre-installed) for attaching
camera module to the back box (x3, silver. Use
provided security torx bit).
2.
Motorized 2.7-13.5mm lens. See LENS ADJUSTMENT section for more information.
3.
IR board.
4.
Video format switch. Default video format setting: HD-TVI.
5.
Power connector (DC12V/AC24V).
6.
BNC video connector. Connect to an encoder, DVR/HVR or service monitor.
Four (4) video formats supported: HD-TVI (
default
), HD-AHD, HD-CVI and CVBS. Use
the video format switch (#4) to set video format as required.
7.
Screws attaching camera bubble to the camera module (x3, silver. Use provided
security torx bit).
8.
Dome bubble.
9.
Camera’s back box. Compatible with i3’s DB60 Goose-neck bracket. Can also be
used for pendant mount installations.
10.
Side conduit hole (3/4”).
Remove plug to route power and video cables through the side opening.
Use the plug for the top conduit hole in that scenario.
When using outdoors, sealant must be used to maintain the IP66 status.
11.
Top conduit hole (3/4”). Can also be used for pendant mount installations.
When using outdoors, sealant must be used to maintain the IP66 status.
12.
Mounting holes, partially drilled, x6 (complete drilling the holes prior to installation).
DISASSEMBLY AND INSTALLATION
Prepare the mounting surface:
• Depending on the type of installation, additional mounting accessories may need to be
purchased.
• It is the installer’s responsibility to ensure that the mounting surface is suitable for the
chosen installation method.
• Based on installation location and surface type, supplied screws and anchors may not
be adequate. Mounting hardware is site-specific and may need to be supplied by the
installer.
• Use silicone sealer around the chosen conduit hole to maintain IP66 rating when
installing outdoors.
SURFACE MOUNTING
Prepare the mounting surface
1.
Use the supplied security Torx key to loosen three screws securing the dome bubble
housing to camera module. Gently pull the dome bubble away from the main camera
module.
2.
Depending on the type of installation and mounting surface, complete drilling 2-3 holes
in the back box in preparation for the mounting.
Prepare the mounting surface
3.
Attach the supplied mounting template to the mounting surface.
4.
Drill holes, as marked on the template and insert supplied anchors into the holes. The
number and positioning of holes must match the ones pre-drilled on the back box in
Step 2.
DIMENSIONS AND DEFINITIONS
E
A
B
Waterproof tape
e Waterproof tape
pe Waterproof ta
f tape Waterproo
oof tape Waterpr
proof tape Water
C
D
HIGH DEFINITION ANALOG VIDEO SUPPORT
Your Am73 camera supports the standard CVBS composite analog video stream
(720x480) and a high-definition (5MP/2MP) video stream in HD-TVI, HD-AHD, and HD-
CVI format. Am73 camera supports a single video output at-a-time. No separate spot
monitor output is offered.
IMPORTANT:
In order to use high-definition video, your Am73 camera
must be
connected to a video encoder
or standalone DVR/HVR that supports HD-TVI,
HD-AHD, or HD-CVI format.
Note:
i3’s line of encoders and embedded standalone DVRs supports HD-TVI and CVBS
formats only.
CHANGING VIDEO FORMAT:
- Go to OSD menu, then change the resolution to 5MP or 4MP.
- Unscrew protection cap from the video format switch (#4 under Dimensions and
Definitions section).
- Press and hold the button for 5 seconds to change the video output format to the
next one in sequence.
Video format sequence:
TVI (default) > AHD > CVI > CVBS.
IMPORTANT:
Am73 is shipped with the video resolution set to 2MP
(NTSC, HD-TVI), for continued compatibility with i3’s line of HR16 encoders.
Veo16p Embedded HVR supports 5MP HD-TVI resolution.
To record full 5MP video with Veo16p, set Am73 resolution to 5M20 in the OSD >
VIDEO FORMAT menu.
See CAMERA OSD MENU section for more information.
1
4
Lens Direction
GUIDE PATTERN
140mm (
5½
”)
Ø147mm (
5¾
”)
Ø99.94mm (3.93”)
HD
1
2
3
3
5
6
7
8
9
10
11
12
