background image

 

ii

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Information provided in this document is solely for use with the USB-to-I2C Professional product 
from SB Solutions, Inc.  SB Solutions, Inc. reserves the right to make changes or improvements to this 
document at any time without notice.  SB Solutions, Inc. assumes no liability whatsoever in the sale 
or use of this product, including infringement of any patent or copyright.  
Reasonable efforts have been made to ensure the accuracy of the information presented.  However, 
SB Solutions, Inc. assumes no responsibility for the accuracy of the information. 
No part of this document may be reproduced or transmitted in any form or by any means, electronic 
or mechanical, for any purpose, without the express written permission of 
SB Solutions, Inc. 
P.O. Box 4506 
Cary, NC 27519-4506 
 
Microsoft and Windows are registered trademarks of Microsoft Corporation. 
Other brand names are trademarks or registered trademarks of their respective owners. 
 
Copyright 

 2004-2017                   

 

 

SB Solutions, Inc.  All rights reserved.                             

Содержание USB-to-I2C















Отзывы: