4
Standard accessories
*1 This label may be required for network management. Use caution not to lose this label.
Attachment plate ×1
Plate cover ×1
Bit ×1
(6.35mm hexagonal, T20)
Grommet ×2
(of them, 1 for spare)
RJ45 cap ×1
Template ×1
Fixing screw ×4 (M4 × 8 mm)
(of them, 1 for spare)
Waterproof RJ45
connector cover/cap ×1
*2 RJ45 Ethernet Cable is attached to the camera.
Other items that are needed (not included)
• Mounting screws
Installation method
Recommended
screw*
1
Minimum pull-out
strength*
2
Directly mount the camera onto the installation surface
M4 × 16 mm
{5/8 inches} × 4 pcs.*
3
196 N {44 lbf}
Mount the camera to a two-gangbox/junction box.
Mount the camera using the exclusively designed mount bracket. Refer to the operating instructions of each bracket.
*1 Select screws according to the material of the location that the camera will be mounted to. In this case,
wood screws and nails should not be used.
*2 This value indicates the minimum pull-out strength required value per screw.
For information about the minimum pull-out strength, refer to our technical information website <Control No.: C0120>.
*3 The screw length is an example when installing the camera on a robust ceiling or wall with a thickness of
20 mm {25/32 inches} or more.
• Ethernet cable with RJ45 plug (category 5e or better, straight, 4 pairs (8 pins))
Installation Guide (this document) ...................... 1 pc.
Installation procedure leaflet ............................... 1 pc.
IMPORTANT SAFETY INSTRUCTIONS .............. 1 pc.
Code label*
1
....................................................... 1 pc.
Specifications*
*
For further information, refer to the “Basic Information”.
Power source*
1,
*
5
:
12 V DC
PoE (IEEE802.3af compliant), PoE+ (IEEE802.3at compliant)
Power consumption*
1
:
■
When using in a state where the tilt speed is 300 °/S
12 V DC:
1.3 A/ Approx. 15.4 W
PoE 48 V DC:
270 mA/ Approx. 12.95 W (Class 0 device)
■
When using in a state where the tilt speed is 500 °/S
PoE+ 54 V DC: 350 mA/ Approx. 18.9 W (Class 4 device)
Operating environment:
Ambient operating temperature:
Ambient operating humidity:
–30 °C to +55 °C {–22 °F to +131 °F}
(Power on range –20 °C to +55 °C {–4 °F to +131 °F})
10 % to 100 % (no condensation)
Storage environment:
Storage temperature:
Storage humidity:
–30 °C to +60 °C {–22 °F to +140 °F}
10 % to 95 % (no condensation)
EXT I/O terminals*
5
:
ALARM IN1 (Alarm input 1/ Black & white input/ Auto time adjustment input) (x1)
ALARM IN2 (Alarm input 2/ALARM OUT) (x1)
ALARM IN3 (Alarm input 3/ AUX OUT) (x1)
Audio input*
5
:
For microphone input:
For line input:
ø3.5 mm stereo mini jack
Recommended applicable microphone: Plug-in power type
(Sensitivity of microphone: –51 dB to –38 dB (0 dB=1 V/Pa, 1 kHz))
Input impedance: Approx. 2 kΩ (unbalanced)
Supply voltage: 2.5 V ±0.5 V
Input level: Approx. –10 dBV
Audio output*
2,
*
5
:
ø3.5 mm stereo mini jack (Audio output is monaural.)
Output impedance: Approx. 600 Ω (unbalanced)
Output level: –20 dBV
Waterproof*
3
:
IP66 (IEC 60529), Type 4X (UL50E), NEMA 4X compliant
Shock resistance:
IK10 (IEC 62262)
Wind resistance:
Up to 40 m/s {approx. 89 mph}
Dimensions:
Maximum diameter: ø165 mm × 139 mm (H) {ø6-1/2 inches × 5-15/32 inches (H)}
Dome radius 63.5 mm {2-1/2 inches}
Mass:
Approx. 1.6 k
g
{3.53 lbs}
Finish:
Main body:
Aluminum die cast, black and PC resin, i-PRO white
Outer fixing screws:
Stainless steel (Corrosion-resistant treatment)
Dome cover:
PC resin,
C
/
G
(Transmittance: 45 %)
Others:
Tamper-resistant enclosure*
4
NEMA TS2 Compliant
Maximum temperature according to NEMA TS 2 (2.2.7): 74 °C (165 °F)
*1 Refer to our technical information website <Control No.: C0106> for further information about Power source
and Power consumption information.
*2 The audio output can be switched to the monitor output. Refer to the “Operating Instructions” on our pro-
duct information website for descriptions of how to switch the output.
*3 Only when installation work is properly performed according to the Installation Guide and appropriate water-
proof treatment is performed.
*4 Component that has a structure on which the screws that are accessible after installation cannot be screwed
or unscrewed using an ordinary screwdriver.
*5 When using a 12 V DC power supply of this product, EXT I/O terminal, audio input, and audio output, I/O
cable (option: WV-QCA501A) is required.
Optional accessories
Base bracket:
WV-QJB501-W
Mount bracket:
WV-QSR501
Base bracket:
WV-QJB504
Dome cover:
WV-QDC502G
Ceiling mount bracket:
WV-QEM503
I/O Cable:
WV-QCA501A
The latest information
→
Technical information website “Accessory Selector” <Control No.: C0501>
RJ45 Ethernet Cable*
2
×1
