Step 2
Attach the cover of this product to the top of the camera.
Recommended tightening torque
: 2.45 N·m {1.81 lbf·ft}
NOTE
Do not use the “cable cover” included with
the camera.
Use a 4 mm {5/32 inches} hexagon
wrench (locally procured) to tighten the
camera fixing screws (3 places).
As shown in the illustration at right, put the
safety wire on the outside of the cover of
this product.
Step 3
Get the ceiling ready and attach the base of this product to the ceiling.
Fixing screws: M8 screws
(flat washer / spring washer)
Minimum pullout strength: 1539 N {346 lbf} (per 1 pc.)
1
Make screw holes or anchor holes in the ceiling,
and also wiring holes if necessary.
<
Possible installation dimensions
>
A: 71.8 mm × 71.8 mm {2-3/16 inches × 2-3/16 inches}
B: 120.5 mm × 120.5 mm {4-3/4 inches × 4-3/4 inches}
2
When wiring through the ceiling, make a ø30 mm
{ø1-3/16 inches} hole in the center.
Cover
Camera fixing
screws (3 places)
Positioning
pin (3 places)
Safety wire
Step 5
Put the cover of this product which has been attached to the top
of the camera so the fitting holes (2 places) fit over the
positioning pins on the base that has been fixed to the ceiling,
the turn clockwise approximately 10° to temporarily fix in place.
Approx. 10°
Fitting hole
(2 places)
Positioning pin
(2 places)
Fitting hole (2 places)
NOTE
When temporarily fixing the camera to the base of this product, make sure you are
holding the cover of this product.
Step 6
Tighten the cover fixing screws (4 places) alternating diagonally
with a 4 mm {5/32 inches} hexagon wrench (locally procured) to
fix the cover attached to the camera to this product. (
1
to
4
)
Recommended tightening torque
: 2.45 N·m {1.81 lbf·ft}
Fixing screws
for cover portion
(4 pleces)
1
2
3
4
<
When wiring through the ceiling
>
Base
Fixing screws (4 pcs.)
(M8: locally procured)
Cap for the
female thread
for the conduit
Flat washer (4 pcs.)
(M8: locally procured)
Spring washer (4 pcs.)
(M8: locally procured)
<
When wiring through the side hole
>
Conduit
When using the conduit on the ceiling
for wiring, remove the cap for the female
thread for the conduit by using a
hexagon wrench (ISO 2936, width across
flats S=5 mm {3/16 inches}).
The female thread for conduit is compliant
with ANSI NPSM (parallel pipe threads) 3/4
or ISO 228-1 (parallel pipe threads) G3/4.
Step 4
Hang the camera from the base of this product with the installed
auxiliary wire and connect the cables.
Surface of the base
installed on the
ceiling
Installed
auxiliary
wire
Wire hook
Wire hook
Wire stopper
Installed auxiliary wire
Ceiling
NOTE
There are some cables to be connected that need to be waterproofed. Refer to the
Installation Guide for the camera for information on which cables need waterproofing and
how to waterproof them.
Step 7
Attach the safety wire of the camera to the wire hook section on
the base of this product.
Safety wire
Wire hook section
Refer to the Operating Instructions for the camera for information about further adjustments
(connecting power to the camera, adjusting the angular field of view).
WV‐QCL500‐S_PGQX2358YAC6_カメラ天井吊り下げ金具_en.indd 2
2021/10/28 14:56:44
