HYVE AQUILADSF, Руководство пользователя

Страница: 13 / 22

HYVE SOLUTIONS | CONFIDENTIAL 13
Warnings
Heed safety instructions:
Before working with your server product, whether you are using this guide or any other resource as a
reference, pay close attention to the safety instructions. You must adhere to the assembly instructions in this guide to ensure and
maintain compliance with existing product certifications and approvals. Use only the described, regulated components specified in
this guide. Use of other products/components will void the UL listing and other regulatory approvals of the product and will most
likely result in noncompliance with product regulations in the region(s) in which the product is sold.
System power on/off:
The power buttons DOES NOT turn off the system AC power. To remove power from the system, you must
unplug the AC power cord from the wall outlet. Make sure the AC power cord is unplugged before you open the chassis, add, or
remove any components. Hazardous conditions, devices and cables: Hazardous electrical conditions may be present on power,
telephone, and communication cables. Turn off the server and disconnect the power cord, telecommunications systems, networks,
and modems attached to the server before opening it. Otherwise, personal injury or equipment damage can result.
Electrostatic discharge (ESD) and ESD protection:
ESD can damage disk drives, boards, and other parts. We recommend that you
perform all procedures in this chapter only at an ESD workstation. If one is not available, provide some ESD protection by wearing an
antistatic wrist strap attached to chassis ground any unpainted metal surface on your server when handling parts.
ESD and handling boards:
Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by their edges.
After removing a board from its protective wrapper or from the server, place the board component side up on a grounded, static
free surface. Use a conductive foam pad if available but not the board wrapper. Do not slide board over any surface.
Installing or removing jumpers:
A jumper is a small plastic encased conductor that slips over two jumper pins. Some jumpers have a
small tab on top that you can grip with your fingertips or with a pair of fine needle nosed pliers. If your jumpers do not have such a
tab, take care when using needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with the pliers,
never the wide sides. Gripping the wide sides can damage the contacts inside the jumper, causing intermittent problems with the
function controlled by that jumper. Take care to grip with, but not squeeze, the pliers or other tool you use to remove a jumper, or
you may bend or break the pins on the board.
CLASS I PLUGGABLE EQUIPMENT TYPE A:
- Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord
- Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan
-
Apparatet må tilkoples jordet stikkontakt
- Apparaten skall anslutas till jordat uttag
Caution
Battery:
Lithium battery included with this server. Do not puncture, mutilate, or dispose of battery in fire. You will run the risk of an
explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of used battery accordingly to the
manufacturer’s instructions and in accordance with your local regulation’s.
Service:
Only trained
personnel’s should install, service or replace parts in this server. The server is for restricted access only.
Power Supply:
The power supply in this server has no user serviceable parts. If the power supply is defective, return the unit for
service.
DC operated Server:
Since this server is DC operated, it will be auto booted up when the server connects to DC power bus bar at
the back of Rack. The power button is provided on I/O panel for server ON-OFF services. For unscheduled service, unplug the
server from Rack will power off the server. For scheduled services, there are 2 ways to shut off the server DC power. The 1
st
way is
to press the power button for about 10 seconds for server to activate its power off sequence. The 2
nd
way is to issue a Linux
command to gracefully shut down the server for servicing.