background image

3.5 Starting and stopping the engine.

3.5.1 Observe all safety precautions in this manual.

3.5.2 Before starting: Turn on blower move switch down(1), set throttle (3) to the 

fast position.

3.5.2.1 If the engine is cold, close (3) the choke (1).

3.5.2.2 If the engine is hot, open (2) the choke fully. Also use this position 

when the engine has been running but is still cold.

3.5.2.3 Press the primer bulb (1) at least 10 times.

3.5.2.4 Put the unit on the ground. Check that bystanders are well clear of the 

general work area and the nozzle.

3.5.2.5 Make sure you have a firm footing:

3.5.2.5.1 Hold the unit with your  left hand on the housing and put one 

foot against the base plate to prevent it slipping.

3.5.2.5.2 Pull the starter grip slowly with your right hand to 20cm and  

give it a brisk strong pull.

3.5.2.5.3 DO NOT pull the starter rope out all the way as it might  

break.

3.5.2.5.4 DO NOT let the starter grip snap back.

3.5.2.5.5 Guide it slowly back into the housing so that the starter rope 

can rewind properly.

3.6 When the engine begins to fire:

3.6.1 If the engine is cold, open the choke and continue cranking until engine 

runs.

3.6.2  If the engine is warm, continue cranking until engine runs.

Page 10

Ver 2

Содержание HYB33

















Отзывы: