manualshive.com logo in svg

Hyundai HY2270001, Руководство по эксплуатации

Поделиться
Скачать
Hyundai HY2270001 Скачать руководство пользователя страница 18

INSPECTION AND MAINTENANCE PROCEDURES

1. AIR CLEANER ELEMENT

By loosing the air cleaner band, and check the
contamination of the element visually.

Inspection

The inspection method varies depending on how dirty the element is.

(A) If dry dust is adhering to the air cleaner element, blow pressurized air (7kg/cm

2

 or

less) from inside of the air cleaner element to remove it.

(B) If the element is soiled with black carbon or soot, remove it with cleaning liquid.

(1) For the cleaning liquid, dissolve 300g (10.6oz) of air element cleaner

(ND1500) into 20   of water. Immerse the air cleaner element for about 20
minutes.

(2) With the dust cap removed, flush the air cleaner element using tap water.
(3) After cleaning, let the element dry in a place where air circulates freely.

The standard inspection is every 100 service hours. However, inspect
every 50 if the machine is used in a dusty environment.

Never use fire or pressurized air to dry the air cleaner element.

!

WARNING

Air cleaner element

- 65 -

Содержание HY2270001



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды