Hyundai HiS-MxxxMF Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 16

Hyundai HiS-MxxxMF Скачать руководство пользователя страница 5

www.hhi-green.com/solar

Page 5 of 16

Sales Office

2nd Fl., Hyundai Bldg.,
75, Yulgok-ro, Jongno-gu,
Seoul 110-793, Korea

Factory

313, Soi-ro, Soi-myeon, Eumseong-gun,
Chungcheongbuk-do 369-872, Korea

3.4 Mounting Method

·

All modules are fixed using mounting holes of long frame.

·

Each module must securely fastened at a minimum of 4 points on two opposite sides, using the most
outer mounting holes.

·

If additional wind loads are anticipated for this installation, additional mounting points should be used.
System designer and installer are responsible for load calculations and for proper design of support
structure.

·

When installing modules in snowy area, additional clamping or supporting parts should be attached to
the middle of the lower long side frame to prevent possible damages from slipping snow.

Detailed mounting method is described in ‘module installation instruction’ in the appendix.

Picture 1. HiS-MxxxMF Hole Position

«
...
3
4
5
6
7
...
»

Содержание HiS-MxxxMF

















Отзывы:

Нет отзывов