Hyundai HiE-S SG Series Скачать руководство пользователя страница 10

Страница: 10 / 13

www.hyundai-es.co.kr

Page 10 of 13

Sales Office

4th Fl., First Tower,
55, Bundang-ro, Bundang-gu,
Seongnam-si, Gyeonggi-do,
13591 Korea

Factory

313, Soi-ro, Soi-myeon, Eumseong-gun,
Chungcheongbuk-do 369-872, Korea

6. Operation and Maintenance

It is required to perform regular inspection and maintenance of the modules, especially within warranty

scope.

It is the user’s responsibility to report to the supplier regarding the damages found.

6.1 Cautions

Do not conduct electrical work such as opening junction boxes or separation of connectors without a

qualified expert.

Before electrical work, remove any metal material from body and wear protection equipment for

insulation.

To minimize output decline, remove any substance near the PV modules such as grass, moss, and

vine.

Any chemical which is not approved by HHGIE shall not contact PV modules.

6.2 Cleaning

Recommend maintaining module glass surface clean as possible to improve module power efficiency

and long life.

HES modules are designed for long life and require very little maintenance. Under most weather

conditions, normal rainfall is sufficient to keep the module glass surface clean.

For AR coating HES modules utilize special materials to increase energy harvest. Always use clean

gloves when handling the module, never touch the glass with bare hands.

If dirt build-up becomes excessive, clean the glass surface with room temperature water and soft

materials without potential risks of scratch. Do not use water with high pressure for cleaning. Do not

use harsh cleaning materials such as scouring powder, steel wool, scrapers, blades, or other sharp

instruments to clean the glass surface of the module. Use of such materials or cleaning will invalidate

the product warranty.

Do not clean the backside of the module. If backside cleaning is necessary, please contact local

representatives for more detailed information.

PV modules will be

“self-clean” as effectively as modules mounted at a 15° tilt or greater.

6.3 Visual Inspection of Modules

Inspect the modules visually to find whether there are appearance defects, the following need to be

paid more attention especially:

1) Whether the glass is broken
2) Corrosion along the cells’ bus-bar
3) Whether there is burning vestige on the Backsheet.

6.4 Inspection of connector and Cable

In order to ensure proper operation of the system, please check all wiring connections and the

condition of the wire insulation periodically.

Содержание HiE-S SG Series














Результаты поиска

Содержание HiE-S SG Series

Отзывы:

Hyundai HiE-S SG Series, Руководство по установке, Страница: 10 / 13

Результаты поиска

Содержание HiE-S SG Series

Отзывы: