Hyundai HDR 12 IVA, Руководство пользователя

Страница: 33 / 39

UP( )/DOWN( ) buttons
Operating
Instructions
· Humidity Set Control buttons
· TIMER Set Control buttons
Use the Up/Down buttons to set the Auto start
and Auto stop time from 0.0 to 24.
The humidity level can be set within a range of 35%
RH(Relative Humidity) to 85%RH(Relative Humidity)
in 5% increments. For drier air , press the button
and set to a lower percent value(%). For damper air,
press the button and set a higher percent value(%).
Display(On some models)
· Shows the set % humidity level from 35% to 85%
or auto start/stop time (0~24) while setting, then
shows the actual(±5% accuracy) room % humidity
level in a range of 30% RH(Relative Humidity) to
90%RH(Relative Humidity).
Error Codes:
EH60-Humidity sensor error--Unplug the unit and
plug it back in. If error repeats, call for service;
EH61-Tube Temperature sensor of the evaporator
error-- Unplug the unit and plug it back in. If
error repeats, call for service;
EH02-Zero-crossing signal detection error; If error
repeats, call for service;
EH03-Indoor fan speed malfunction; If error repeats,
call for service;
EH0b-Indoor PCB and display board communication
error; If error repeats, call for service;
Protection Code:
P2-Bucket is full or bucket is not in right position--
Empty the bucket and replace it in the right
position. On some models, the water full light
illuminates.
Note: When one of the above malfunctions occurs,
turn off the unit, and check for any obstructions.
Restart the unit, if the malfunction is still present,
turn off the unit and unplug the power cord.
Contact the manufacturer or its service agents or a
similar qualified person for service.
FAN speed/ button
· Control the fan speed.Press to select fan speed
in three steps-low, med and high.The fan speed
indicator light illuminates under different fan
speed settings.
· Press and hold the Fan speed button for 3 seconds
to eliminate filter reminder, when the filter light
flickers(On some models).
Note: The unit operates for 250 hours, then enter
filter clean reminder.
indicator light illuminates. All current settings are
locked, and the control panel will not accept any
operation except of the LOCK.
· Press and hold these two buttons button again to
cancel the LOCK feature .
FRESH
/
button(On some models)
· Press FRESH buttons to initiate FRESH feature,
and the fresh indicator light illuminates(The fresh
indicator light and the UV indicator light illuminate
at the same time on some models; Only the UV
indicator light illuminate on some models ).The ion
generatoris energized and UV (UltraViolet) feature
will help to purify the air inside.Press FRESH buttons
again to stop FRESH feature, and the fresh indicator
light turns dark.
Wireless button(On some models)
· If connection (router) is successful within 8 minutes,
the unit will exit Wireless connection mode automa-
tically and the Wireless indicator illuminates and the
unit enters the previous function. If connection is
failure within 8 minutes, the unit exits the Wireless
connection mode automatically.
· Press and hold on the POWER button for 3 seconds
to initiate the Wireless connection mode. The LED
DISPLAY shows’AP’ to indicate you can set Wireless
connection.
Quick glance light
/
button(On some models)
· Press buttons to illuminate the quick glance
light or turn quick glance light dark.
· When the humidity is more than 65%, the quick
glance light will emit red light.
· When the humidity range is at 45% to 65%, the
quick glance light will emit green light.
· When the humidity is lower than 45%, the quick
glance light will emit yellow light.
NOTE: When the unit is connecting to internet, the
quick glance light will flash white light.
NOTE: When bucket full or clean filter is on, the quick
glance light will emit orange light and turn off 1sec
every 4 sec.
LOCK feature(On some models)
· Press and hold on the Up and Down buttons
for 3 seconds to initiate LOCK feature, and the Lock

Page 13
