background image

Genuine Accessories

Electronic Installation Instructions

Glasses

Gloves

Mask

Hearing Protection

Part Weight (Gross)

FMVSS 110 Compliance Information

1)
2)

3)
4)
5)
6)

• Evenly distribute the load
• Ensure the crossbars are secure.

• Precaution must be taken when operating vehicle's sunroof with crossbars and attachments installed.

WARNING

• Never exceed 165 lbs (75 kg) on top of crossbars.

Failure to adhere to load limits and distribution requirements may result in loss of vehicle control, severe personal injury, or death.

• Always check the height of the vehicle when crossbars and attachments are installed before driving under tunnels or parking
  structures with low bridges.

NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.

Clean Cloth

Step Ladder

Tape Measure

10.60

lbs

All dealers must determine if the Net weight they have added in the form of  all options or accessories, when added to the weight of all Port/Dealer Installed 
options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs.  If the additional weight does exceed the lesser of the indicated thresholds, a “Load 
Carrying Capacity Reduced” label must be installed.  A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying 
capacity in kilograms or pounds, which is the total weight of all added options and accessories.     

Load Label Part Number:  NP070 - 09003

4.80

kg

Notes to the installer:

Read the entire Installation Instructions prior to beginning the installation of this accessory.
If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as a replacement, register the removal of 
the old part before registering the new part. Old and new parts will have different barcode data, and the old registration cannot be reused.

REGULARLY CHECK THE TIGHTNESS BY PERFORMING A TUG ON CROSSBARS.THEY SHOULD NOT MOVE. 
If crossbars move, see step 3~5 for proper tightening. Incorrect clamp tightness can cause crossbar separation from vehicle resulting in 
product failure and vehicle damage. Serious physical injury may occur.

Torque Wrench

Coin or Flat-Head 

Screwdriver

Loads must be evenly distributed and secured. Failure to achieve the distribution requirements may result in loss of vehicle control, severe personal injury, or death.

Any weight carried on the vehicle will adversely affect its handling, particularly in cornering or in a cross wind and the vehicle should therefore be driven with increased caution.

Only use NON-STRETCH tie down straps. Use of stretch elastic tie downs may cause loss of load, potential serious injury, and vehicle damage.

Never exceed 165 LBS (75 KG) on top of crossbars. 

Failure to adhere to load limits may result in loss of vehicle control, severe personal injury, or death.

Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.

(B) Dealer Technician
(C) Master Technician or Specialist

If this is a printed copy of the installation instructions, ensure you have the latest revision by
scanning the QR code or by entering the website address listed below before beginning installation.
Use the latest revision date as noted by “Rev. Date” above.

www.hyundaiaccessories.com/admin_media_uploads/installationSheets/cwf21_au000.pdf

Instructional Symbols / Definitions

Denotes warnings that may lead to 
serious physical injury or vehicle damage

Denotes quality processes to be checked 
prior to moving to the next step

Denotes personal protective equipment (PPEs) that 

may be required for a step.  Examples of safety 

equipment icons noted below:

Application Notes

Does NOT apply to models equipped with a Panoramic Roof

Denotes cautions to be taken to avoid 
physical injury or electronic component 
damage

Denotes specific tools that are necessary 
to complete a step

N
O
T
E

Denotes important information to be 
reviewed during the step

5mm Allen Socket

Denotes cautions to be taken to avoid 
vehicle and component damage

Basic Required Tools

Copy OEM Logo Here  (

)

Vehicle Model: Tucson

Accessory: Crossbars

Difficulty stated above reflects the minimum level of 
expertise required to install the accessory:

Language

English

Model Year

2022~

Difficulty:

( A )

Part No.

CWF21 AU000

Note:

Rev. Date

1/28/2021

(A) Customer     

5560668001

Revision Date

01/28/2021

Page 1 of 6

Отзывы: