Hypro Turbo Stream 1508B-130EFS Скачать руководство пользователя страница 1

Страница: 1 / 12

5/11 Rev. B

Form L-1530

Turbo Stream

Installation, Operation, Repair and Parts Manual

Description

The Hypro High Pressure System is a gas motor-driven,

flow-based proportioning system that injects foam concen-

trate at a desired percentage at a fixed water flow rate. The

basic Hypro High Pressure System is shown below. The

system will accurately deliver from 0.3% to 3.0% foam con-

centrate at the rated system pressure and flow rate. The

system will accurately inject foam concentrate while the

system is running at recommended operating speed and

pressure. Foam percentage indication is instantaneously

given on the foam monitoring panel supplied.

The foam concentrate is directly injected into the system at

the head of the pump. It is then fed as foam solution into

the adjustable foam spray gun.

The pump inlet is equipped with a check valve to prevent

contamination of the water supply.

The Hypro High Pressure Foam System is designed for

Class A foam concentrate (per NFPA 1150) applications

and calibrated for viscosity ranges up to 60 CPS.

Model No. 1508B-130EFS

Содержание Turbo Stream 1508B-130EFS












