Limited Warranty on Hypro Pumps and Other Hypro Products
Hypro Corporation (“Hypro”) warrants to the original purchaser of its products (the “Purchaser”) that such products will be
free from defects in material and workmanship under normal use for the period of one (1) year for all products except: oil
crankcase plunger pumps will be free from defects in material and workmanship under normal use for the period of five (5)
years, and accessories will be free from defects in material and workmanship under normal use for the period of ninety
(90) days. In addition, Hypro warrants to the purchaser all forged brass pump manifolds will be free from defects in
material and workmanship under normal use and from damage resulting from environmental conditions for the life of the pump.
“Normal use” does not include use in excess of recommended maximum speeds, pressures, vacuums and temperatures,
or use requiring handling of fluids not compatible with component materials, as noted in Hypro product catalogs, technical
literature, and instructions. This warranty does not cover freight damage, freezing damage, normal wear and tear, or
damage caused by misapplication, fault, negligence, alterations, or repair that affects the performance or reliability of the
product.
THIS WARRANTY IS EXCLUSIVE. HYPRO MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Hypro’s obligation under this warranty is, at Hypro’s option, to either repair or replace the product upon return of the entire
product to the Hypro factory in accordance with the return procedures set forth below. THIS IS THE EXCLUSIVE REM-
EDY FOR ANY BREACH OF WARRANTY.
IN NO EVENT SHALL HYPRO BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND,
WHETHER FOR BREACH OF ANY WARRANTY, FOR NEGLIGENCE, ON THE BASIS OF STRICT LIABILITY, OR
OTHERWISE.
Return Procedures
All pumps or products
must be flushed of any chemical (ref. OSHA Section 0910.1200 (d)(e)(f)(g)(h)) and hazard-
ous chemicals
must be labeled before being shipped* to Hypro for service or warranty consideration. Hypro
reserves the right to request a Material Safety Data sheet from the Purchaser for any pump or product Hypro deems
necessary. Hypro reserves the right to “disposition as scrap” pumps or products returned which contain unknown sub-
stances, or to charge for any and all costs incurred for chemical testing and proper disposal of components containing
unknown substances. Hypro requests this in order to protect the environment and personnel from the hazards of handling
unknown substances.
For technical or application assistance, call the Hypro Technical/Application number: 1-800-445-8360.
To obtain service or warranty assistance, call the Hypro Service and Warranty number: 1-800-468-3428;
or call the Hypro Service and Warranty FAX: (651) 766-6618.
Be prepared to give Hypro full details of the problem, including the following information:
1. Model number and the date and from whom you purchased your pump.
2. A brief description of the pump problem, including the following:
•
Liquid pumped. State the pH and any non-soluble
•
Drive type (gas engine/electric motor; direct/belt drive;
materials, and give the generic or trade name.
tractor PTO) and rpm of pump.
•
Temperature of the liquid and ambient environment. •
Viscosity (of oil, or other than water weight liquid).
•
Suction lift or vacuum (measured at the pump).
•
Elevation from the pump to the discharge point.
•
Discharge pressure.
•
Size and material of inlet and outlet line.
•
Size, type, and mesh of the inlet strainer.
•
Type of spray gun, orifice size, unloader/relief valve.
Hypro may request additional information, and may require a sketch to illustrate the problem.
Contact the factory to receive a return material authorization before sending the product. All pumps returned for warranty
work should be sent shipping charges prepaid to:
HYPRO CORPORATION
Attention: Service Department
375 Fifth Avenue NW
New Brighton, Minnesota 55112-3288
*Carriers, including U.S.P.S., airlines, UPS, ground freight, etc., require specific identification of any hazardous materials being shipped.
Failure to do so may result in a substantial fine and/or prison term. Check with your shipping company for specific instructions.
.
Printed in the USA
2000 Hypro Corporation
Conformance to 89/392/EEC (machine directive), as well as,
73/23/EEC (low voltage) and 89/336/ECC (electromagnetic
compatibility) as declared in standard EN809.
