Hypertherm Echion Скачать руководство пользователя страница 39

Страница: 39 / 194

Operation

Echion

Operator

Manual 810770

rat

Operator interface

Primary operation screen

These elements are on most screens.

Refer to

Touchscreen maps

on page 175 to see all of the screens available on the controller.

1 Hour meter

This shows the total hours the pump motor has
been in operation.

2 Primary operation screen tab

• Turn the pump on or off.

• Select the pressure mode (cut or pierce).

• Set or change the water pressure.

• Monitor the status of the intensifier.

3 Operator interface: Adjustment screens tab

• See information about your system.

• Change some display options, such as

pressure units (bar or psi) or language.

• Change timer durations.

• Turn features such as Modbus mode on or

off.

Refer to

Operator interface: Adjustment screens

on page 164.

4 Operator interface: Maintenance screens tab

• Move the plunger to one end of the

intensifier.

• Prepare the pump for storage.

• See the alarm log.

• See the inputs-outputs from the controller.

Refer to

Operator interface: Maintenance

screens

on page 56.

5 Date and time

Refer to

Date / Time / Language

on page 169.

Содержание Echion



































































































































































































Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды

Hypertherm Echion, Руководство оператора

Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды