LITHIUM POLYMER/ION MODE
(for 3.7V/cell types only!)
Number of LiPo Cells Wired in Series (Pack Voltage)
1S
3.7V
2S
7.4V
3S
11.1V
4S
14.8V
5S
18.5V
6S
22.2V
LiPo CHARGE
C=3300mAh 6S
LiPo DISCHARGE
D=1.00 A 6S
LiPo CHARGE
C=3300mAh 6S
LiPo CHARGE
C=3300mAh 6S
BATTERY CHECK
WAIT PLEASE. . . .
BALANCER CON.
CONNECTED
CHG 0:00 00000
LP + 2.20A 22.200V
LiPo DISCHARGE
D=1.00A 6S
LiPo DISCHARGE
D=1.00A 6S
BATTERY CHECK
WAIT PLEASE. . . .
BATTERY CHECK
WAIT PLEASE. . . .
START
INC
INC
INC
INC
DEC
DEC
DEC
DEC
INC
DEC
BATT TYPE
START
ENTER
ENTER
ENTER
ENTER
DCH 0:00 00000
LP + 1.00A 22.200V
Setting LiPo battery capacity
Adjust and set the correct battery capacity from 100mAh to 20000mAh with INC & DEC buttons
(50mAh per step). Press the ENTER button to confirm setting. Charge rate is set on the basis of
selected capacity, at 1C rate. Example: Li-Po cell of 1500mAh capacity: 1C = 1500mA (= 1.5A).
LiPo CHARGE
C=6000mAh 6S
LiPo CHARGE
Setting Battery Voltage / Number of Cells in Series for LiPo battery packs
Select the total battery voltage to be charged with ENTER, INC & DEC buttons.
C=6000mAh 6S
LiPo DISCHARGE
The charger knows the pack’s voltage both from the balancer connector and the cell count e.g. ‘6S’
NOTE: The EOS Series chargers have intelligent detection routines to help you avoid making
mistakes, and LOW or HIGH VOLTAGE errors are displayed if battery voltage does not match your
setting. HOWEVER, under some circumstances, especially with over-discharged or damaged
batteries, the safeguard could fail. Therefore, be absolutely sure that you have correctly set pack
voltage correctly before charging, every time!
Using the cell balancer for all Lithium packs is
STRONGLY recommended, as it greatly increases safety.
Setting discharge parameters
Adjust to the desired discharge current from 0.10A to 1.00A (0.01A per step) with INC & DEC button.
Press the ENTER button to confirm setting. Set pack voltage, 1S~6S as in charging example above.
Autocut occurs automatically at 3.0V per cell.
D=1.00 A 6S
LiFe MODE [LiFePO4, A123]
The LiFe charge/discharge modes are intended for cells with 3.3V nominal, with Lithium Phosphate chemistry. The LiFe
(LiFePO4 charge/discharge modes are intended for cells with 3.3V nominal produced by A123 Company, or other-brand
LiFePO4 cells which are recognized to be of good quality from well-known makers. Choose LiFe for BATT TYPE, for charging
such cells. The LiFe charge mode MAY work with “no brand” LiFePO4 cells having 3.3V nominal voltage, but Hyperion has
found some “knock off” cells in the market of very questionable quality. Customers who use A123 mode (LiFePO4
mode) to charge such off-brand cells assume all risk. In no case does Hyperion HK Ltd. Accept liability due to the
failure of the cell(s) during charging or discharging.
Due to the nature of A123/LiFePO4 cells (wide divergence in cell voltages during charging) and due to the high rates at which
some of these cells – such as A123 brand – can be charged, one MUST ALWAYS properly use the cell balancer function
whenever charging in LiFe Mode; failure to do so will result in poor pack performance at best, and damage to cells at worst.
Customers who charge in LiFe mode without balancer connected assume all risk of charger and battery failure!