DIAGRAM
SPECIFICATIONS
Video format:
AVI
Video resolution: 720 x 480
Photo format:
JPEG
Image ratio:
4:3
Input:
DC-5V 200mAh
Storage support:
Micro SD card
Battery type:
Rechargeable lithium
Supported Memory:
16G of
micro SD card
(Max)
Charging Interface:
USB
Operating Instructions
1. Status Indicator
• Blue: video-recording mode
• Red: camera-mode
• Red and Blue: video is currently recording
2. Turning Camera On/Off
• Insert the micro SD card.
• Press the ON/OFF switch.
• The lights will cycle through red lights, blue lights to
initialize the camera. When the red light turns off, the
device will enter standby mode.
• Press the ON/OFF switch until the blue light turns off
to turn the device off.
3. Manual Recording Mode
•Hold the operation button for 2 seconds to start the
5
Hype
®
reserves the right to exchange the product for a
replacement product of equal value if the product
sent in cannot be repaired within a reasonable time or
at a reasonable cost. Requests cannot be made for
repairs to be carried out on site. Parts that have been
replaced or exchanged become our property.
4) The warranty claim does not apply if repairs or other
work is carried out by unauthorized persons or if our
products are equipped with additional parts or
accessories that are not approved for our product.
5) Warranties that have been activated do not cause
the warranty period to be extended, nor do they
trigger a new warranty period. The warranty period for
any replacement parts installed ends with the warranty
period for the entire product.
6) Any other further claims are excluded, especially
those for replacement due to damage caused to the
outside of the product, provided there is no obligatory
legal liability. We therefore accept no liability for
accidental, indirect or other consequential damage
of any kind, which leads to usage restrictions, data loss,
and loss of earnings or interruption to business.
Asserting a warranty claim:
1) To make use of the warranty service for hardware
issues, you must contact the Hype
®
Service Center by
email at [email protected]
2) Hype
®
will try to diagnose and solve your problem. If
it is determined that a warranty claim exists, you will be
given an RMA number (Return Material Authorization)
and will be asked to send the product to Hype
®
.
IMPORTANT: Hype
®
will only accept parcels that have
an RMA number.
Please observe the following when sending the
product:
1) Send the product suitably packaged with carriage
and insurance paid. Do not enclose any accessories
with the product (cables, chargers, manuals, etc.)
unless the Hype
®
Service Center specifies otherwise.
2) Mark the RMA number on the outside of the
package in such a way that it is visible and clearly
legible.
3) You must enclose a copy of the sales slip as proof of
purchase.
voice recording function.
• The blue light will flash slowly 3 times and turn off.
This will indicate the device is recording voice.
• Press the OPERATION button quickly and the
device will stop recording voice.
Video recording mode:
•At standby mode, quick press the On/Off button, the
blue LED light will flash 3 times consecutively and the
video recording function will start.
• Connect device to a computer to retrieve your
.avi format video.
• To ensure the size and the quality of the video, the
device is programmed to auto-save every 10 minutes
during recording and continue recording.
4. Taking a Photo
• In standby mode, press the operation button quickly.
• The blue light will turn off. The red light will flash
once and turns off.
• The device will save a .jpeg file and return to
standby mode.
Note: To ensure your videos and photos are
adequately lit, ensure the camera is not obstructed
by any objects, and film your subjects with a
distance greater than 18” (50cm). To ensure good
sound, do not block the microphone.
5. Connecting to Computer
• Ensure the device is turned on.
• Using the enclosed USB cable, connect the
device to a computer .
• The computer will recognize the device as a
“Removable Disk”
• During the first connection, please wait 30
seconds while the device installs necessary drivers
onto your computer. Do not disconnect it during
this time.
• After you have reviewed, saved, or deleted any
video, right click on the “Removable Disk” and
select “Eject.”
• Do not disconnect the device from your computer
until your device says it is safe to remove.
6. Webcam Usage
• Connect to computer USB interface using the
enclosed cable
• After the device is recognized by your computer
as a “Removable Disk,” press On/Off the button quickly
• If your computer supports webcam functionality,
the device will begin recording as a webcam.
• If your computer does not support this device as a
webcam, you may need to download additional
software. Please visit “amcap.en.softonic.com” to
download a free software called AMCap that may
assist in compatibility. Please note, DGL Group is not
responsible for any software or hardware problems
resulting from the download and use of AMCap.
7. Charging your Device
Connect your device to a computer or a certified
wall charger using the enclosed mini USB cable.
During charging, the red LED will remain lit. When
the battery is fully recharged, the red LED light will
turn off automatically. Charging may take up to 2
hours.
8. Setting Time
• Install micro SD card into device.
• Turn off the camera and connect to a computer.
• Open the Removable Disk.
• Select “tag.txt” and open.
Type in the date/time in the following format
YEAR.MO.DAY - HR:MIN:SEC
Please note, you will need to follow a 24-hour
military time format. Below is an example:
“2012.05.01 23:59:59
The above time string shows the time you want to
set. Pay attention to the space between
Year/Month/Day and Hours Minutes and Seconds.
9. Automatic Shutdown
• When the device is recording, if power is low, the
green LED light will flash 4 times, and the device will
automatically shut down to save battery life.
• When the micro SD card’s memory is full, the green
LED light will flash 4 times, and the device will automati-
cally shut down to save the current file.
10. Reset the watch
Press the mode and operating keys simultaneously.
FCC STATEMENT
This equipment has been tested and found to comply
with the requirements for a Class B digital device under
Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, usesand can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does case harmful
interference radio or television reception, which can
be determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following measures.
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Do not attempt to repair or modify this equipment.
WARNING: Changes or modifications to this
equipment not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment and invalidate the
warranty claim.
WARRANTY INFORMATION
The condition of this warranty and our responsibilities
under this warranty are as follows:
Supplier’s warranty is non-transferable. And this warranty is
limited to the original purchaser only.
* You must be able to prove the date of original purchase
of the unit with a dated receipt.
* The warranty is not applicable if the product has been
