Dual Mode LED T8 Tube - Installation/Retrofit Guide
Technical Data
Model:
HL-GT8-4F-18W-30K HL-GT8-4F-18W-40K HL-GT8-4F-18W-50K
Length:
4 ft. / 120cm
4 ft. / 120cm
4 ft. / 120cm
Power:
18W
18W
18W
CCT:
WarmWhite (3000°K)
Neutral White (4000°K)
Daylight (5000°K)
Lumens:
2100 lm
2100 lm
2200 lm
CRI:
>80 >80 >80
Beam Angle: 300°
300°
300°
Volts:
120-277VAC, 50/60Hz.
120-277VAC, 50/60Hz.
120-277VAC, 50/60Hz.
Current:
40~230mA 40~230mA 40~230mA
PF:
>0.9 >0.9 >0.9
•
Risk of Fire or Electric Shock. Read and Understand all Installation Instructions before installing HyLite T8 LED Tube Light.
HyLite LED Bi-pin tube lights are designed to work with Electronic/Magnetic Ballasts or AC Direct Wire.
For installing the Tube with AC Direct Wire Connection, only one end of the tube is designated as the input side. Please ensure only this end is installed
in the Powered Lamp Holder. Do not Remove Cover and/or End Caps. No User-Serviceable Parts inside.
• WARNING: Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt
installation. Contact a qualified electrician.
• The installer must determine and verify whether they have AC 100~277V at the luminaire before installation. Improper voltage matching can result in
performance degradation and/or physical damage.
• Risk of Fire - If the Lamp or Luminaire Exhibits Undesirable Operation (Buzzing, Flickering, etc.),
immediately
Turn-Off Power, remove Lamp from Luminaire
and contact Qualified Electrician or HyLite LED Lighting
• This Lamp Only Operates on Electronic and Magnetic Ballasts. If Lamp Does Not Light when the Luminaire
is Energized, remove Lamp from Luminaire
and contact Qualified Electrician or HyLite LED Lighting
• Do Not Install this Lamp in a Pre-Heat Luminaire
• This Lamp Complies with Part 15 of the FCC Rules. Operation is Subject to the following two conditions:
1. This Device may not cause Harmful Interference, and,
2. This Device must accept any interference received, including interference that may cause undesired operation
• WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• HyLite LED Tubes should only be installed by a qualified electrician and in accordance with all the applicable installation codes. Always contact ground
lead to luminaire in accordance with national, state,and/or local electrical codes where applicable. Failure to do so may result in a serious personal injury.
• Luminaires Wiring, Ballasts, or other Electrical Parts may be damaged when installing. Always check for enclosed Wiring and Components.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during installation.
• Not for Emergency Lighting. This Device is Not intended for use with Emergency Exits
“Plug & Play” Procedure:
1. Turn-off Power to the Fixture at the Breaker Panel before Installation. Ensure no Power is going to the Fixture
2. Open the Diffuser from the Fixture
3. Remove the Fluorescent Tube. Please dispose of Fluorescent Tube properly as per local ordinances, since they contain Mercury. Please recycle.
4. Install the HyLite LED Tube into the Fixture
5. After the Installation the HyLite LED Tube, close the Diffuser
6. Turn-on the Power
WARNING -
I
MPORTANT SAFETY INSTRUCTIONS
!
Installation Method for 4 ft. (120cm) HyLite T8 LED Tube
Blue
Blue
Red
Black
White
Electronic
Ballast
HyLite LED Tube
HyLite LED Tube
Blue
Blue
Red
Black
White
Electronic
Ballast
Fluorescent Tube
Fluorescent Tube
Thank you for purchasing HyLite LED Tube Light and
for investing in the future of eco-friendly products.
By selecting HyLite LED Tube Light you have chosen a
high-quality, eco-friendly product that is designed for
years of dependable performance. We trust you will
experience years of reliable service from it. This guide
explains the steps necessary to install or retrofit the
T8/T10/T12 tube lights to ensure optimal performance.
This guide is for reference only and is intended for
qualified electricians or lighting technicians. HyLite LED
Tube Lights are intended to retrofit maximum four
lamps, surface mount, or Non-IC recessed mount
fluorescent luminaries that use straight tubular Tube Lights.
Contents:
1. Single-End Power LED Tube Light
2. Label to be placed on the retrofit Luminaire
3. Installation/Retrofit Guide
