HygroMatik WaterLine Double Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 44

HygroMatik WaterLine Double Скачать руководство пользователя страница 30

Page 30

8. Maintenance

8.1 General information

The HygroMatik softener device requires only very little mainte-
nance by design. In order to guarantee the water quality desired,
however, periodically performed checks of the device are impor-
tent. Daily control of proper operation is just one activity to start
with. Beyond that, an extended life-time of the HygroMatik
WaterLine softener device may only be achieved when pro-
grammed maintenance is carried out.

With respect to standards and regulations relevant for drinking
water supplies, we recommend that the following intervals are
met:

•

bimonthly inspection of the device by the device operator

•

minor maintenance every 6 months by the device operator

•

full maintenance once per year by an expert company for
water treatment

Warning:

When carrying out maintenance works pls. keep in

mind:

•

only expert staff may do the maintaining

•

always obey security regulations

•

Prior to maintenance work shut-down operation of device
and secure system against switching on (pull power adap-
tor)

•

After finishing maintenance work, have device checked for
operational safety by expert personnel

8.2 Maintenance work to be carried out by the

device operator

8.2.1 Daily check of proper device operation

Visual inspection

Check device for leakiness. Leaking components should be
made tight by technical staff. No kinks are allowed in feeding or
draining hoses.

Check raw water hardness

In case of a deviation from set value, settings may be required to
be changed by technical staff.

Check soft water hardness

In case of a deviation from set value, settings may be required to
be changed by technical staff.

«
...
28
29
30
31
32
...
»

Содержание WaterLine Double













































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды