background image

COMPATIBILITY

 

 

This acoustic device is only compatible with conventional control panels and systems, unless an approved optional module is fitted. For more 

specific information regarding compatibility refer to your fire security system supplier and the technical documentation concerning the control 

panel in use.

 

 

INSTALLATION 

-

 IMPORTANT NOTES

 

 

Refer  to  national  and  international  standards  in  use  for  spacing  and  positioning  of  the  fire  security

s  system  devices;  refer  also  to  specific 

standards and your supplier if the system is going to be installed in particular environments or environments where specific risks exist.

 

 

This device is to be used only with conventional control panels and systems (check the COMPATIBILITY paragraph).

 

 

This device must be wired according to the connection details described in this manual.

 

 

Disconnect the sounder line from the control panel before installing this device.

 

 

Test the device after installation.

 

 

SOUNDER OPENING PROCEDURE

 

 

In order to detach the upper sounder body from the base:

 

 

1)

 

Insert the pins of the compatible key into the holes of one of the two side locking mechanisms.

 

 

2)

 

Turn the key 90° to the left whilst applying light pressure.

 

 

3)

 

Repeat this step for the second side locking mechanism; the locking mechanism appears as in picture 1 when 

in the open position (flush).

 

 

4)

 

Detach the sounder body from the base by pulling gently to separate (picture 3).

 

 

SOUNDER CLOSING PROCEDURE

 

 

In order to assemble the sounder body to the base:

 

 

1)

 

Assemble the sounder body to the base using gentle pressure (picture 3).

 

 

2)

 

Insert the pins of the compatible key into the holes of one of the two side locking mechanisms.

 

 

3)

 

Turn the key 90° to the right.

 

 

4)

 

Repeat this step for the second side locking mechanism, starting from point 2; the locking 

 

 

mechanism appears as in picture 2 once closed (recessed).

 

 

5)

 

To secure use the retaining screws, using the location holes on both sides of the base (picture 4).

 

Picture 1

 

Picture 2

 

Picture 3

 

Hyfire Wireless Fire Solutions Limited 

-

 Unit B12a, Holly Farm Business Park, Honiley, 

 

Warwickshire, CV8 1NP 

-

 United Kingdom

 

www.hyfirewireless.com

 

HFC

-

WSR

-

03

 

CONVENTIONAL WALL SOUNDER

 

928w/07 

 

Picture 4

 

Содержание HFC-WSR-03









Отзывы: