Performance and Specifications
Item
Number
Model
Number
Softening
Capacity (kilograins)
@10lb/cf
(1)
Color Removal
Capacity (ppm-gallons)
@10lb/cf
(1)
Service
Flow Rate
(2)
USGPM (LPM)
Maximum
Flow to Drain
USGPM (LPM)
Mineral
Tank Size
(3)
inches (mm)
Brine
Tank Size
(3)
inches (mm)
Resin
Volume
cu.ft. (litres)
Anion Resin
Volume
cu.ft. (litres)
Salt
Capacity
Lbs. (kg)
Shipping
We
ight
Lbs. (kg)
7377
WTCA45
12
2,000
8 (30.3)
2.4 (9.1)
10 x 54 (254 x 1372) 22 x 38 (559 x 965)
0.50 (14)
1.00 (28)
420 (191)
100 (45)
Caution: These water conditioners are not intended to be used for treating water that is microbiologically unsafe or of unknown quality without adequate
disinfection before or after the system.
Notes:
1. “*” designates that 10 lb/cf is the factory salt setting for all units.
Operating Temperature Range:
110°F (43°C)
2. Capacities of softeners may deviate from the chart above depending on flow rates and raw water
Operating Pressure Range:
100 psig (689 kPa)
conditions.
Electrical:
Standard 110V
3. The manufacturer reserves the right to make product improvements which may deviate from the
Pipe size:
3/4””
specifications and descriptions stated herein without obligation to change previously manufactured
products or to note the change.
4. 1 Kilograin is equal to 1000 grains.
Application and Installations for the
Combination OCR Removal & Softener Unit
This Combination Softener has been designed to remove tannins and hardness from your water supply. Tannins can cause
a yellow to brown colour in the water (i.e. organic colour) and also may impart taste and odour as well. Tannins are formed
by the decomposition of vegetable matter. Hardness is responsible for the deposition of calcium carbonate scale in pipes
and equipment.
All tannins are not equal, the unit selected should have been with the assistance of an authorized representative or
distributor. This is typically done based on a water analysis and column testing of the source water and/or with experience
on other successful installations in the area on the same source water.
Application Notes about Combination OCR Removal & Softener Unit:
1. Although the Combination unit was selected using the source water, the selected Combination unit was the most
suitable for this application, total removable of all colour contaminants may occasionally not be attained due to:
a) Multiple types of tannins in the source water. Unit media may only be successful at removing some of these
organics, but not all.
b) Colour may be caused by contaminants other than organics.
c) The remaining contaminants may require removal by other methods such as activated carbon, reverse
osmosis, etc. Please consult your authorized representative or distributor for solutions.
2. Metals in the water such as Iron and Manganese can also foul the Combination resin bed, reducing the ability to remove
tannins and hardness. An iron filter or iron guard softener should be used to reduce the problem causing contaminants
to an acceptable level.
(
Installation Tip: Ensure that the Combination unit is only allowed to regenerate after the regeneration of
the filter unit, if one is present.)
3. Turbidity caused by suspended solids and sediment can foul the Combination resin bed. Removal of the turbidity can
be achieved through some type of mechanical filtration such as a multi-media filter and/or cartridge filters.
4. Depending on the alkalinity of the source water being treated, the pH (alkalinity) of the water after the Combination unit
will likely drop for part or all of the units service run after regeneration. This is caused by the Combination unit’s resin
ability to also remove alkalinity in the water. Adjustment of the waters pH may be required once treated by the
Combination unit.
5. If “nitrates” are present in the source water, consult your authorized representative or distributor for additional solutions.
(Caution: This unit has not been designed for nitrate removal and should be dealt with separately
.
)
6. Occasionally, a fishy odour will occur if the source water is of a high pH, typically greater than 8.0. If this occurs, putting
the unit through a couple regeneration cycles can sometimes reduce the odour. Chlorine in combination with a higher
pH can also make the odour worse or more difficult to overcome as chlorine degrades the resin in the Combination unit.
7. Depending on the alkalinity of the source water being treated, the chlorides in the treated water from the Combination
unit will increase proportionally. This may result in a bitter salty taste which should be treated with a reverse osmosis
drinking water system for household drinking and cooking water.
1
Содержание 5600 Calendar Clock Valve
Страница 2: ......
