Hydronix Hydro-Control VI Скачать руководство пользователя страница 40

Страница: 40 / 104

Commissioning

Chapter 4

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0

General Settings

Parameter

Units

Default

Range

Language

None

English

Multiple Languages

Max Mix Logs

None

100

1-1000

Archiving

None

True

True/False

The

Language

parameter sets the Hydro-Control to display different languages.

The

Max Mix Log

parameter limits the maximum number of mix logs saved to the database.

The

Archiving

parameter, when selected, will enable the HC06 to save all mix log data that

exceeds the Max Mix Logs limit to an archive file. Once the Max Mix log limit has been reached

any Mix Logs that are removed from the main database are copied to the archive file. If a USB

memory stick is inserted into the HC06, and a Backup is requested, the archive files will be

copied to the USB stick. This will enable the user to keep a record of older mix logs.

Alarms Setup

The Alarms Setup section on the System Parameters page allows each of the alarms in the

system to be disabled. The alarms are described in the Operators Guide in the chapter ‘Alarm

Configuration’.

At the end of a batch, if the sensor value has not fallen below the

Mixer Blades Worn Value

by the end of the

Mixer Blades Worn Time

, then the

Mixer Blades Worn Alarm

is activated.

5.3

The System Parameters – Page 3

By clicking the Next button

the internal temperature and voltage monitoring page is

displayed. This is for system information only.

The screen shown in Figure 26 displays the current parameters available from the Hydro-

Control and is used for diagnostic monitoring purposes.

Figure 26: The voltage and temperature monitor screen

Содержание Hydro-Control VI









































































































Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды

Hydronix Hydro-Control VI, Руководство по установке

Результаты поиска

Содержание Hydro-Control VI

Отзывы:

Бренды по названию

Популярные бренды