HydroMatik FlexLine FLE05 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 52

background image

Page 36

»

Clean the strainer.

»

Unscrew the hand nuts (A).

»

Remove electrodes (B).

»

Clean electrodes and check elec-
trode wear (s. „Changing electrodes“
section).

»

Check sensor electrode for salt
deposits and remove them if neces-
sary (until metallically bright).

»

Check the inside of the top part of
steam cylinder for crust build-up and
possible salt bridges (black grooves
between the electrode leads).

»

Remove the deposits by scraping /
scrubbing them off.

»

Replace the O-rings of the elec-
trodes.

»

Install new electrodes (48). Make
sure that the electrodes are posi-
tioned correctly (see exploded view).

The deposits in the upper part of the cylinder
can be conductive and lead to unwanted cur-
rents between the electrode connections and
the sensor electrode and thus to the mes-
sage "cylinder full".

If electrical bridges have penetrated deep
into the material, the steam cylinder must be
replaced.

»

Check the base and its connections
for limescale deposits and clean if
necessary.

»

Insert a new O-ring in the base.

»

Insert new O-rings between the cyl-
inder halves, in the base and in the
steam hose adapter.

A

B

HINWEIS

«
...
34
35
36
37
38
...
»

Содержание FlexLine FLE05





















































Отзывы:

Нет отзывов

Похожие инструкции для FlexLine FLE05

Бренд: Haier Страницы: 28

Бренд: Ecoair Страницы: 15

Бренд: Ecoair Страницы: 17

Бренд: Goldair Страницы: 8

Бренд: Stadler Form Страницы: 30

Бренд: Stadler Form Страницы: 77

Бренд: Munters Страницы: 32

Бренд: Mitsubishi Страницы: 48

Бренд: Lacme Страницы: 27

Бренд: Ecor-Pro Страницы: 64

Бренд: SPT Страницы: 7

Бренд: Objecto Страницы: 17

Бренд: Nortec Страницы: 8

Бренд: RFS Страницы: 98

Premiere DDR30A1GP

Бренд: Danby Страницы: 24

Бренд: Quincy Страницы: 38

HealthMist 4100

Бренд: Kaz Страницы: 6

Бренд: Danby Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды