manualshive.com logo in svg

Hydro systems 113205, Руководство по эксплуатации

Поделиться
Скачать
Hydro systems 113205 Скачать руководство пользователя страница 4

English: 4

Installed directly in the fluid supply line, the injector operates without electricity, using fluid (water) 

pressure as the power source. The fluid drives the injector, which pulls the required percentage of 

concentrate directly from the chemical solution container. Inside the Hydro Systems patented mixing 

chamber, the concentrate is mixed with the fluid, and the fluid pressure forces the mixed solution 

downstream. The amount of concentrate will be directly proportional to the volume of fluid entering 

the injector, regardless of variations in flow or pressure. 

Fluid flow drives 

motor piston.

Chemical does not 

come in contact 

with the motor. 

Chemical is mixed 

in the patented 

mixing chamber.

Blended solution

Intake from chemical 

container

Operating Principle

Accurate and Reliable

→

→

→

→

→

*MiniDos model shown, example only. 

SuperDos 20 is not equipped with on/

off lever.

Содержание 113205






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды