Hydro Instruments HC-220 Скачать руководство пользователя

Страница: 11 / 16

V. OPERATION MODE

How to Enter/Exit:

See Section I.2a on page 3.

Overview:

When the HC-220 is in use it should be in this mode. This mode displays input values, output

value and alarm conditions. This mode is used to set dosage, Residual (or ORP or pH) setpoint
and for manual override of chemical feed rate.

1. Flow Pacing Mode:

Operation in direct proportion to a fl ow meter signal.

1a. Select Automatic or Manual Control Mode.

Choose

AUTO/MANL

(Use to change selection)

DISPLAY

(PV1)

O Flow Rate

(%, GPM, MGD, …)

DISPLAY (PO1)

Chemical Feed Rate

(%, PPD, …)

1b. Select the Dosage level which is desired.

DOSAGE

0.01-9.99 adjustable with

and

keys

1c. In Manual Mode the feed rate will be displayed and can be adjusted with

and

keys.

DISPLAY (PO1)

Chemical Feed Rate

(%, PPD, …)

1d. Alarm messages are displayed.

DISPLAY

ALARMS

(none, Flow Signal Loss, …)

2. Residual/ORP/pH Control Mode:

Control by Residual, ORP, or pH input only.

2a. Select Automatic or Manual Control Mode.

Choose

AUTO/MANL

(Use to change selection)

DISPLAY (PV2)

PV2 Reading

(PPM, MGL, mV, pH)

DISPLAY (PO1)

Chemical Feed Rate

(%, PPD, GPH, …)

2b. Select the Residual/ORP/pH Set Point which is desired.

PV2 Set Point (SV2)

Adjustable with

and

keys

2c. In Manual Mode the feed rate will be displayed and can be adjusted with

and

keys.

DISPLAY (PO1)

Chemical Feed Rate

(%, PPD, …)

2d. Alarm messages are displayed.

DISPLAY

ALARMS

(none, Res/ORP Signal Loss, …)

3. Compound Loop Mode:

(PID Control by Flow and Residual/ORP/pH inputs)

3a. Select Automatic or Manual Control Mode.

Choose

AUTO/MANL

(Use to change selection)

DISPLAY

(PV1)

O Flow Rate

(%, GPM, MGD, …)

DISPLAY (PO1)

Chemical Feed Rate

(%, PPD, …)

3b. Select Automatic or Manual Control Mode.

Choose

AUTO/MANL

(Use to change selection)

DISPLAY (PV2)

PV2 Reading

(PPM, MGL, mV, pH)

DISPLAY (PO1)

Chemical Feed Rate

(%, PPD, GPH, …)

3c. Select the Residual/ORP Set Point which is desired.

PV2 Set Point (SV2)

Adjustable with

and

keys

3d. Select the Dosage level which is desired.

DOSAGE

0.01-9.99 adjustable with

and

keys

Содержание HC-220

















Результаты поиска

Содержание HC-220

Отзывы:

Похожие инструкции для HC-220

Бренды по названию

Популярные бренды

Hydro Instruments HC-220, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание HC-220

Отзывы:

Похожие инструкции для HC-220

Бренды по названию

Популярные бренды