1.Introduction
Thank you for purchasing our Digital Ballast. Please review the following
instructions to ensure you receive the best performance. Each ballast uses
a high temperature, resin-sealed component board for completely silent
operation without a fan. Each unit is burned-in at the factory for approximately
twelve hours to ensure maximum reliability.
Our Digital Ballast uses a mirco-processor similar to your home computer.
To ensure safe operation, it is programmed or a “soft-start” and does not
require an initial surge of power to light the lamp. This increases the lamp life
and allows the end user to start multiple ballasts at the same time without
tripping breakers. In case of auto-shut off, please disconnect from the power
supply, remove the faulty lamp or check for wiring problems, then restart
your ballast.
2.Controls, Connections and Indications
A.Digital ballast
B. Output plug
C.IEC connector for power cord
D . Power cord with NEMA 6-15 plug
NEMA 6-15
3. Product Information
3.1. Technical specifications
3.2. Main Dimension
3.3. HOT SPOT
Tcase max=75°C
3.4 Environment
The product is meant for use in climate rooms. The product may be used in
damp environments. The product may not be used in wet environments or
outdoors. The 630W Doubled Ended CMH Lamp functions optimal when the
ambient temperature is between -20 ~ 40° Celsius / -4 ~ 104° Fahrenheit.
4.Wiring Diagram
-Ballast Case must be Grounded
5.Protections
1.End of Lamp Life(EOL)Protection
2.Short circuit protection
3.Open circuit protection
4.Ignition failure protection
5.Thermal protection
6.Warning
Power surge, power outage, outage overloading may stress or damage the
lamp. As a safety feature, the Soft-Start technology also reduces ballast
damage caused by a bulb failure. In case of an unexpected shut-off, please
disconnect from the power supply, remove the faulty lamp, check for wiring
problems, then plug-in the ballast power cord.
7.Disclaimer
Any of the following circumstances will not be warrantied:
1. Product damaged due to incorrect installation of the product without
following the wiring diagram.
2. Damaged by improper use or submerging in water and not following the
manual instruction.
3. Install or use of the product without following local laws and regulations.
4. Damage due to maintenance or repair of the product by an unauthorized
technician.
5. Use in an environment that does not meet the provisions indicated in the
manual.
6. Damaged by mishandling, abnormal voltage, earthquake, flood, fire,
transportation accidents, etc.
IMPORTANT PRODUCT INFORMATION
READ IMMEDIATELY
SAFETY FIRST!
Failure to observe the following safety warnings may result in serious injury
or death. Use all products only as directed. Failure to observe these safety
warnings will result in a waiver of any and all liability on the part of its
manufacturer, and resellers, and will void all warranties to the extent
permitted by law.
WARNINGS AND INSTRUCTIONS
FOR USE:
• Disconnect power before re-lamping.
• When re-lamping, make sure lamp has time to cool before touching.
• Make sure power cord is connected properly.
• DO NOT hang ballast by power cord or lamp cord.
• DO NOT make contact with the interior of the socket while the power is on.
• DO NOT plug or unplug a lamp cord while the ballast is turned on.
• ALWAYS unplug the ballast from the power source before connecting or
disconnecting any lighting device to ballast, moving ballast, or otherwise
touching or handling ballast or its components.
• DO NOT use with generators. Warranty will be voided.
• NEVER stand beneath the ballast.
• NEVER put hands or any other objects in the interior of the ballast.
• DO NOT operate this or any lighting system in wet areas.
• NEVER get the ballast wet or allow it to come into contact with water or
any other liquids.
• NEVER drop, shake or jostle the ballast.
• NEVER attempt to insulate or otherwise cover the ballast, as it releases a
great deal of heat and may cause a fire or other damage. Ballasts should
always have plenty of room to breathe and good ventilation around them.
• DO NOT plug this system into a supply voltage other than what is
instructed on your fixture.
• DO NOT attempt open or rewire the components of the light system. It will
void the warranty and may cause serious injury or death.
• NEVER attempt to rewire or alter any internal or external mechanisms or
components on the ballast. This includes trying to cut and/or rewire
the cords.
Version
630W
3.5kg/7.72lb
75 °Celsius / 167 °Fahrenheit
-20 ~ 40 °Celsius / -4 ~ 104 °Fahrenheit
120V
5.78A
686W
>0.95
< 15%
50-60Hz
IEC C14
5 kV
≤50 Amps
Nema 6-15
240V
2.86A
270.5mmx181.5mmx102mm
Product weight
Dimensions (L*W*H)
Temperature case
Temperature ambient
Input v/-10%
Input current at 100%
Input power at 100%
Power factor
Total Harmonic Distortion
Frequency
Power inlet
Ignition voltage:
Inrush current:
Plug type:
HOT SPOT
1
5A
1
2
5V
~
E
2
06
1
44
C
B
A
D
Page 1
Page 2
Page 3
