HydraMaster Steamatic 8800 TMU Скачать руководство пользователя | Manualshive

Страница: 31 / 148

background image

2-5 - Installation Information

Steamatic 8800 TMU

SettIng up tHe SteamatIC 8800 tmu

Prior to operating the Steamatic 8800 TMU, follow these steps:

Adjust the vacuum relief located on the recovery tank by capping all the vacuum

1.

inlets. The machine should be set to 12” Hg maximum.

Setting the vacuum level higher than the recommended value can result in an
increased risk of serious component damage.

The Steamatic 8800 TMU is shipped from the factory with antifreeze added to the solution
system.

Recover this antifreeze and dispose of the recovered antifreeze as stated in the local laws
and regulations.

KeeP ANTIfReeZe oUT of ReACH of CHIlDReN AND ANIMAlS. Drinking
antifreeze can cause death.

If required, dispose of antifreeze at facilities licensed to accept household
hazardous waste. If permitted, dispose of antifreeze in sanitary sewer systems.
Do not pour antifreeze into storm sewers, septic systems, or onto the ground.
Doing so causes health and environmental dangers.

ensure the antifreeze is completely drained from the solution system. If any
antifreeze remains in the system, it could damage machine components and
damage fabric.

«
...
29
30
31
32
33
...
»

Содержание Steamatic 8800 TMU





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Steamatic 8800 TMU

Бренд: NARGESA Страницы: 33

Бренд: Major Страницы: 52

Бренд: Malekko Страницы: 2

Бренд: Major Страницы: 26

Бренд: Yamaha Страницы: 39

Бренд: Yamaha Страницы: 110

Бренд: Jackson Страницы: 2

Бренд: Vag Страницы: 10

Cell Saver Elite+

Бренд: Haemonetics Страницы: 230

Heart Guardian AED

Бренд: Radian Страницы: 36

UltraVent XS Plus 6 2/3 E

Бренд: Rational Страницы: 220

Бренд: Kaiweets Страницы: 6

Бренд: Kaiweets Страницы: 6

Бренд: Kellfri Страницы: 44

Бренд: Wang Страницы: 146

Бренд: RAB Страницы: 4

Бренд: HOMCOM Страницы: 11

Powerator 1800 compact

Бренд: Seto Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды