manualshive.com logo in svg

HydraMaster Diamond Products GTXR+, Руководство владельца и журналы технического обслуживания

Поделиться
Скачать
HydraMaster Diamond Products GTXR+ Скачать руководство пользователя страница 32

  Diamond Products GTXR+ - Owner’s Guide:  30

FREEZE GUARDING

To avoid permanent damage to the truckmount, it is imperative to follow the freeze guard 

procedure whenever the possibility of freezing temperatures exists.

When disposing of antifreeze follow local laws and regulations. Do not discard 

into storm sewers, septic systems, or onto the ground.

Antifreeze is harmful or fatal if swallowed. Do not store in open or unlabeled 

containers. Keep out of reach of children and animals. 

Freeze Guard Procedure

1.  With the truckmount turned off and the incoming water line disconnected, open 

the water box drain valve on the front of the truckmount. Allow the system to fully 
drain.

2.  Add 2 gallons of 50/50 antifreeze and water mix to the water box.
3. 

Attach a section of solution hose to the outgoing solution fitting on the front of the 
machine. Attach  the  opposite  end  to  the  recirculation  fitting.  (If  more  sections  of 

hose are to be freeze guarded attach those inline.) 

4.  Start the truckmount and allow it to run for 2 to 3 minutes. This will distribute antifreeze 

solution throughout the truckmount.

5.  Remove the chemical feed line from the chemical jug. Turn the selector valve to 

“PRIME.” This will vacuum the chemical remaining in the lines to the recovery 
tank.

If using the recirculation kit, skip ahead to step 7.

6.  Remove the quick connect from the truckmount.
7.  Spray the antifreeze and water mix out of the truckmount and into a container to 

reclaim the solution. Run the truckmount until there is no more solution coming from 
the truckmount..

8. 

The  truckmount  is  now  freeze  guarded.  Remember  to  flush  antifreeze  from  the 

system prior to carpet cleaning. See the following procedure.

Содержание Diamond Products GTXR+


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды