HydraMaster CTS 403 Flex Скачать руководство пользователя страница 121

Страница: 121 / 140

Assemblies and Parts Lists: 8-50

Figure 8-40.

Sacrificial Anode Assembly

610-029-724 Rev. B

DETAIL B

SCALE

2 : 2.5

DETAIL A

SCALE

2 : 2.5

LTR

REVISION DESCRIPTION

CODE

DATE

CHKD APPVD

000-108-025 WAS 000-108-022; 000-094-034 WAS

000-094-058; 000-094-150 WAS 000-094-027. FIXED

000-025-098 BOM DESC.

9/18/2019

T.D.L.

P.E.

C 000-025-098 31.0" WAS 36.0"

12/17/2019

P.T.

P.E.

ITEM NO. QTY.

DESCRIPTION

MATERIAL

PART NO.

WASHER, #10 FLAT

S. STEEL

000-174-001

WASHER, #10 EXTERNAL STAR

STEEL

000-174-015

SCREW, #10-24UNC x 1.25" LG. HEX HEAD

S. STEEL

000-143-171

SCREW, #10-24UNC x 0.75" LG. HEX HEAD

S. STEEL

000-143-132

PROTECTOR, MAGNESIUM ANODE - UNMODIFIED

MAGNESIUM

000-108-025

NUT, 10-24 S/S NYLOK HALF

S. STEEL

000-094-150

NUT, #10-24UNC HEX NYLOCK

S. STEEL

000-094-034

CLAMP, WIRE SLEEVE 1/16Ø S-STEEL

S. STEEL

000-033-149

CABLE, 1/16 S-STEEL - 31"

S. STEEL

000-025-098

BRACKET, SACRIFICIAL ANODE - FABRICATED

5052-H32

000-015-1413

APPLICATION

- - -

610-003-801

CDS 4.8

NEXT ASSY

USED ON

SACRIFICIAL ANODE, MAGNISIUM

REV

000-079-226

12/17/2019

8/21/2019

USED ON

NEXT ASSY

APPLICATION

WEIGHT:

PART NUMBER

UNLESS OTHERWISE NOTED

DIMENSIONS ARE IN INCHES

BREAK ALL SHARP EDGES 0.005-.015

SIZE

11015 47th Avenue West,

Mukilteo, Washington 98275

PROPRIETARY INFORMATION

SHEET 1 OF 1

SCALE: 1:8

APPVD

CHECKED

DRAWN

125

MACHINE

FINISH

T.D.L.
P.E.

P.E.

70G URT

610-003-741
610-003-728

100G URT

610-003-763

100G URT

610-003-423

610-003-080

100G URT

TOLERANCES

.X= .1

.XX= .03

.XXX= .010

ANGULAR = 2°

CODE:

0.205

Sacrificial Anode Assembly Parts List

Item Part Number

Description

Qty

000-015-1413

BRACKET, SACRIFICIAL ANODE - FABRICATED

000-025-098

CABLE, 1/16 S-STEEL - 31”

000-033-149

CLAMP, WIRE SLEEVE 1/16Ø S-STEEL

000-094-034

NUT, #10-24UNC HEX NYLOCK

000-094-150

NUT, 10-24 S/S NYLOK HALF

000-108-025

PROTECTOR, MAGNESIUM ANODE - UNMODIFIED 2

000-143-132

SCREW, #10-24UNC x 0.75” LG. HEX HEAD

000-143-171

SCREW, #10-24UNC x 1.25” LG. HEX HEAD

000-174-015

WASHER, #10 EXTERNAL STAR

000-174-001

WASHER, #10 FLAT

DETAIL B

SCALE

2 : 2.5

DETAIL A

SCALE

2 : 2.5

LTR

REVISION DESCRIPTION

CODE

DATE

CHKD APPVD

000-108-025 WAS 000-108-022; 000-094-034 WAS

000-094-058; 000-094-150 WAS 000-094-027. FIXED

000-025-098 BOM DESC.

9/18/2019

T.D.L.

P.E.

C 000-025-098 31.0" WAS 36.0"

12/17/2019

P.T.

P.E.

ITEM NO. QTY.

DESCRIPTION

MATERIAL

PART NO.

WASHER, #10 FLAT

S. STEEL

000-174-001

WASHER, #10 EXTERNAL STAR

STEEL

000-174-015

SCREW, #10-24UNC x 1.25" LG. HEX HEAD

S. STEEL

000-143-171

SCREW, #10-24UNC x 0.75" LG. HEX HEAD

S. STEEL

000-143-132

PROTECTOR, MAGNESIUM ANODE - UNMODIFIED

MAGNESIUM

000-108-025

NUT, 10-24 S/S NYLOK HALF

S. STEEL

000-094-150

NUT, #10-24UNC HEX NYLOCK

S. STEEL

000-094-034

CLAMP, WIRE SLEEVE 1/16Ø S-STEEL

S. STEEL

000-033-149

CABLE, 1/16 S-STEEL - 31"

S. STEEL

000-025-098

BRACKET, SACRIFICIAL ANODE - FABRICATED

5052-H32

000-015-1413

APPLICATION

- - -

610-003-801

CDS 4.8

NEXT ASSY

USED ON

SACRIFICIAL ANODE, MAGNISIUM

REV

000-079-226

12/17/2019

8/21/2019

USED ON

NEXT ASSY

APPLICATION

WEIGHT:

PART NUMBER

UNLESS OTHERWISE NOTED

DIMENSIONS ARE IN INCHES

BREAK ALL SHARP EDGES 0.005-.015

SIZE

11015 47th Avenue West,

Mukilteo, Washington 98275

PROPRIETARY INFORMATION

SHEET 1 OF 1

SCALE: 1:8

APPVD

CHECKED

DRAWN

125

MACHINE

FINISH

T.D.L.
P.E.

P.E.

70G URT

610-003-741
610-003-728

100G URT

610-003-763

100G URT

610-003-423

610-003-080

100G URT

TOLERANCES

.X= .1

.XX= .03

.XXX= .010

ANGULAR = 2°

CODE:

0.205

Содержание CTS 403 Flex













































































































































Результаты поиска

Содержание CTS 403 Flex

Отзывы:

Похожие инструкции для CTS 403 Flex

Бренды по названию

Популярные бренды

HydraMaster CTS 403 Flex, Руководство пользователя

Результаты поиска

Содержание CTS 403 Flex

Отзывы:

Похожие инструкции для CTS 403 Flex

Бренды по названию

Популярные бренды