manualshive.com logo in svg

HydraMaster CDS 4.6, Руководство пользователя, Страница: 116 / 126

Поделиться
Скачать
HydraMaster CDS 4.6 Скачать руководство пользователя страница 116

10-3:  Machine Maintenance

Quarterly

Change oil in blower. 

• 

Change oil in pump. 

• 

Check the vehicle fuel lines for any chafing or wear, especially in the engine compartment 

• 

or near any rotating parts. 

Check the CDS wiring harness for any chafing or wear, especially in the vehicle engine 

• 

compartment or near any rotating parts. 

Check the vehicle wiring harness for any chafing or wear, especially in the vehicle 

• 

engine compartment or near any rotating parts. 

Check  CDS  blower  mounting  fasteners,  drive  shaft  clamping  collar  fasteners,  and 

• 

CDS front end component fasteners, tighten as needed.

Grease the drive shaft spline if so equipped.

• 

Grease the power pack pillow block bearings.

• 

Yearly

Give truck complete vehicle service. 

• 

flush the truck’s cooling system. Add new anti-freeze. 

• 

Change the truck’s transmission fluid.

• 

Perform Descaling As Required

Scale deposits on the interior of the heating system can cause a noticeable loss in heating 

performance. Deposits of this kind result from hard water deposits, excessive chemical 

use or improper chemicals. The frequency with which descaling procedures are required 

will vary. If your area has particularly hard water or you see evidence of deposits in the 

water system, you may have to descale monthly. 

To descale your system:

Add an appropriate descaler chemical to your water box.

1. 

Circulate it through the heating system. let it stand.

2. 

flush and repeat as necessary.

3. 

Clean all screens and strainers, and check them frequently following descaling.

4. 

If you are circulating a descaler through the flowmeter, make sure to run clean water 

through the flowmeter after you perform this procedure.

Содержание CDS 4.6































































































































Отзывы:

Нет отзывов