HydraMaster BoxxerXL Скачать руководство пользователя

Страница: 46 / 144

Operating Instructions: 4-6

SHUt DOWn prOCeDUre

1. flush clean water through the chemical system for 10 seconds. Turn the Chemical

Selection Valve to “Off.”

2. Cool the truckmount down by turning the Pump Clutch switch to “PuMP ON - NO

HeAT”. Spray the cleaning wand into the vacuum hose for 3-5 minutes. The chemical

should now be flushed from the truckmount,

hoses and cleaning tool.

3. Press the Pump Clutch switch to "Off".

4. Remove the vacuum hose.

5. Lubricate the blower to prevent it from rusting

internally.

a. Allow the unit to run for a few minutes with

the vacuum hose disconnected and with the

throttle in the high position (counterclockwise)

in order to remove moisture from the blower.

b. Cap off the inlet(s) to the recovery tank.

c. Spray a HydraMaster-recommended spray

lubricant into the Blower Lube Port for about

5 to 10 seconds while the unit is running (see

figure 4-6).

d. Allow machine to run additional 2 to 5

minutes under load to flush off lubricant.

e. uncap the inlet(s) and run the unit for

another minute to allow the blower to cool

down.

6. If freeze guarding is necessary, perform the

procedure at this time. See the freeze Guarding

section of this Owner’s Manual (see page 5-18).

7. Turn the throttle cable knob to the “IDLe”

position (all the way clockwise).

8. Turn the ignition switch to “Off.”

9. Drain the water box using the water box drain

valve.

10. Drain the recovery tank in an appropriate

location.

In accordance with ePA, state and local laws, do not dispose of water into gutters,

storm drains, streams, or reservoirs.

11.

Perform daily maintenance as specified in Section

5 of this Owner’s Manual.

figure 4-6. Location of Blower

Lube port

Blower

Lube port

Содержание BoxxerXL

















































































































































Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды

HydraMaster BoxxerXL, Руководство пользователя

Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды