Hydac MCS 13 series Скачать руководство пользователя страница 59

Страница: 59 / 80

Error analysis / remedy

MCS

en(us)

Page 59 / 80

BeWa MCS1000 3435427g V13x en 2014-07-16.doc

2014-07-16

Error analysis / remedy

Using several supply voltages makes it necessary to define the following
terms for error analysis:

Designation

Description

Operation voltage Voltage for operating the MCS (electronics, coil

system).

Measurement
voltage

Voltage U

M1/2

at switching output 1/2 for superordinate

controllers.

Signal value

Measurement voltage on = high
Measurement voltage off = low

Remove the connection cable on the MCS for error analysis and check the
socket on the connection cable according to the following steps:

Step

Pin <-> Pin Description

<-> 3

Check the operation voltage.

<-> 4

Check the measurement voltage U

at the

switching output 1

<-> 4

Check the measurement voltage U

at the

switching output 2

Содержание MCS 13 series

















































































Результаты поиска

Содержание MCS 13 series

Отзывы:

Hydac MCS 13 series, Руководство по эксплуатации и установке, Страница: 59 / 80

Результаты поиска

Содержание MCS 13 series

Отзывы: