Hydac Filtromat OF5 F Скачать руководство пользователя страница 46

Страница: 46 / 80

5 | Setting up / assembly / integration of the filter unit

HYDAC FILTER SYSTEMS GMBH

46 / 80

BeWa OF5F-OF5L 3160337h en-us lq

5.7 Inserting the filter element

The filter unit has no filter element installed upon delivery from
the factory. Before commissioning check whether a filter ele-
ment is present in the filter housing.
Install a filter element if it is not already installed. For details,
see

Changing the filter element [

}

55]

5.8 Commissioning

Observe and check the following points for commissioning:

Install the new filter element in the filter bowl. For de-

tails, see Changing the filter element.

Check that the power supply cable is undamaged. Re-

place damaged cables immediately.

Connect the filter unit with the power supply

Check that the suction and pressure hoses are undam-

aged. Replace damaged hoses immediately.

Check the ambient and fluid temperature.

Prior to each use, match the oil type in the filter unit to

the oil type to be pumped. If you are not sure what sort

of oil is in the filter unit, or if you would like to pump a dif-

ferent type of oil than was most recently pumped, empty

the filter unit completely and replace the filter element.

Содержание Filtromat OF5 F

















































































Результаты поиска

Содержание Filtromat OF5 F

Отзывы:

Похожие инструкции для Filtromat OF5 F

Бренды по названию

Популярные бренды

Hydac Filtromat OF5 F, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Filtromat OF5 F

Отзывы:

Похожие инструкции для Filtromat OF5 F

Бренды по названию

Популярные бренды