HYDAC FILTER SYSTEMS FCU1315 Скачать руководство пользователя страница 12

Страница: 12 / 185

HYDAC FILTER SYSTEMS

General |

BeWa FCU1315 4168086b

7 /

2. General

This manual was prepared to the best of our knowledge. Nev-

ertheless and despite the greatest care taken, it may contain

errors. Therefore, please understand that, in the absence of

any provisions to the contrary hereinafter, our warranty and lia-

bility – for any legal reasons whatsoever – are excluded in re-

spect of the information in this manual. In particular, we shall

not be liable for lost profit or other financial loss.

This exclusion of liability does not apply in cases of intent and

gross negligence. Moreover, it does not apply to defects which

have been deceitfully concealed or whose absence has been

guaranteed, nor in cases of culpable harm to life, physical in-

jury and damage to health. If we negligently breach any mate-

rial contractual obligation, our liability shall be limited to fore-

seeable damage. Claims due to the Product Liability shall re-

main unaffected.

2.1. Warranty

For the warranty provided by us, please refer to the Terms of

Delivery. They are made available to you at the conclusion of

the contract at the latest. You will also find these under

www.hydac.com

General Terms and Conditions

(T&C).

2.2. © HYDAC FILTER SYSTEMS GMBH, 2018

Distributing and copying this document and utilizing and dis-

closing its content is not permitted, except where this has been

agreed upon explicitly. Any infringement will entail liability for

granted or a utility model or the design being registered.

We reserve the right to changes to the contents of this manual

without prior notice.

Содержание FCU1315


























































































































































































Результаты поиска

Содержание FCU1315

Отзывы:

Похожие инструкции для FCU1315

Бренды по названию

Популярные бренды

HYDAC FILTER SYSTEMS FCU1315, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание FCU1315

Отзывы:

Похожие инструкции для FCU1315

Бренды по названию

Популярные бренды