manualshive.com logo in svg

HY Technologies F2R4B, Руководство пользователя

Поделиться
Скачать
HY Technologies F2R4B Скачать руководство пользователя страница 9

 

 

- 8 -

  Troubleshooting (for Beeper Only System, F2R4B , F4R4B)   

 

Problem Cause 

Solution 

No beeping when 
reversing or 
parking forward 
with braking 

1. Beeper not connected properly. 
2. No power to the control box. 
3. Faulty beeper. 

 

1. Check beeper connection to control box. 
2. Check control box power connections to see 

if: Black wire is grounded properly,          
Red wire gets +12V from ACC or ignition, 
Yellow wire gets +12V from reverse light,   
Blue wire gets +12V from brake light. 

3. 

Replace the beeper.

System is not 
detecting any 
obstacle in front 
and rear 

1. Beeper not connected properly. 
2. No power to the control box. 
3. Sensors not connected. 
4. Faulty beeper. 
5. Faulty control box. 
 

1. Check beeper connection. 
2. Check control box power connections to see 

if: Black wire is grounded properly,          
Red wire gets +12V from ACC or ignition, 
Yellow wire gets +12V from reverse light,   
Blue wire gets +12V from brake light. 

3. Make sure sensors plugged in securely. 
4. Replace the beeper. 
5. Replace the control box. 

System is not 
detecting any 
obstacle in front   

System has no +12V from brake light. 
 

Make sure the blue wire gets +12V from brake 
light. 
 

System is not 
detecting any 
obstacle in rear 

System has no +12V from back up light. 
 

Make sure the yellow wire gets +12V from 
reverse light. 
 

Beeps 
continuously 

1. Object within 1 ft is detected. 
2. Holes drilled for sensors are too tight 

(especially if it is a metal bumper). 

3. Faulty sensor(s).   
4. Faulty control box. 

 

1. Unplug all sensors, and then plug back in one 

sensor at a time to find out which sensor is       
causing the problem. Check if anything within 
1 ft of the sensor may be detected. Adjust 
angle of the sensor. Refer to 

5. Installing the 

Sensors

 for details. 

2. Carefully enlarging sensor holes a little with a 

small round file. 

3. Replace the sensors(s). 

4. 

Replace the control box.

Beeps even there 
is no obstacle 
behind or in the 
front 

1. Ground is detected. Sensors angle is 

low. Sensors installed too low 
(mounting height below 1.6ft). 

2. 

Holes drilled for sensors are too tight 
(especially for a metal bumper). 

 

1. Unplug all sensors, and then plug back in one 

sensor at a time to find out which sensor is 
causing the problem. Adjust angle of the 
sensor. Refer to 

5. Installing the Sensors

 for 

details. 

2. Carefully enlarging sensor holes a little with a 

small round file. 

 

 
 
 
For more installation related questions and Frequently Asked Questions (FAQs) with 
answers, and product photos, visit our Web site at 

http://parkingsensors.net

   

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

All Rights Reserved 

 HY Technologies 

 Milpitas 

 California 

 USA 

 

http://parkingsensors.net

 

 

Содержание F2R4B













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды